辞职报告中英文对照

2020-04-05 来源:辞职报告收藏下载本文

推荐第1篇:中英文对照

共轨技术

随着人们对低油耗、低废气排放、发动机低噪声的需求越来越大,对发动机和燃油喷射系统的要求也越来也高。对柴油发动机燃油喷射系统提出的要求也在不断增加。更高的压力、更快的开关时间,以及根据发动机工况修订的可变的流量速率曲线,已经使得柴油发动机具有良好的经济性、低污染、高动力性,因此柴油发动机甚至进入了豪华高性能轿车领域。达到这些需求的前提是拥有一个可以精确雾化燃油并具有高喷油压力的燃油喷射系统。同时,喷油量必须精确计算,燃油流量速率曲线必须有精确的计算模型,预喷射和二次喷射必须能够完成。一个可以达到以上需求的系统即共轨燃油喷射系统。

共轨系统包括以下几个主要的部分: ①低压部分,包含燃油共轨系统组件。

②高压系统,包含高压泵、油轨、喷油器和高压油管等组件。

电控柴油机系统EDC主要由系统模块,如传感器、电子控制单元和执行机构组成。共轨系统的主要部分即喷油器。它们拥有一个可以快速开关喷嘴的执行阀(电磁阀或压电触发器),这就允许对每个气缸的喷射进行控制。

所有的喷油器都由一个共同的油轨提供燃油,这就是“共轨”的由来。 在共轨燃油喷射系统中,燃油喷射和压力的产生是分开的。喷油压力的产生与发动机转速和喷油量无关。EDC控制每个组件。

(1) 压力产生。

燃油喷射和压力的产生是通过蓄能器分离开来。将具有压力的燃油提供给为喷射做好准备的共轨系统的蓄能器。

由发动机驱动的连续运转的高压泵提供所需喷油的压力。无论发动机的转速高低,还是燃油喷射量的多少,油轨中的压力均维持在一定值。由于几乎一致的喷油方式,高压泵的设计可以小的多,而且它的驱动转矩可以比传统燃油喷射系统低,这源于高压泵的负载很小。

高压泵是径向活塞泵,在商用车上有时会使用内嵌式喷油泵。 (2) 压力控制

所应用的压力控制方法主要取决于系统。

一种控制油轨压力的方式是通过一个压力控制阀对高压侧进行控制。不需喷射的燃油通过压力控制阀流回到低压回路。这种控制回路允许油轨压力对不同工况(如负载变化时)迅速做出反应。

在第一批共轨系统中采用了对高压侧的控制。压力控制阀安装在燃油轨道上更可取,但是在一些应用中,它被直接安装在高压泵中。

另一种控制轨道压力的方式是进口端控制燃油供给。安装在高压泵的法兰上的计量单元保证了泵提供给油轨精确的燃油量,以维持系统所需要的喷油压力。

发生故障时,压力安全阀防止油轨压力超过最大值。

在进口端对燃油供给的控制减少了高压燃油的用量,降低了泵的输入功率。这对燃油消耗起到积极的作用。同时,流回油箱的燃油温度与传统高压侧控制的方法相比得到了降低。

双执行器系统也是一种控制轨道压力的方式,它通过计算单元对压力进行控制,并且通过压力控制阀对高压端进行控制,因此同时具备高压侧控制与进口端燃料供给控制的优势。

(3) 燃油喷射

喷油器直接将燃料喷到发动机的燃烧室。它们由与燃油轨道直接相连的短高压油轨提供燃油。发动机的控制单元通过与喷油器结合在一起的控制阀的开闭控制喷油嘴的开关。

喷油器的开启时间和系统油压决定了燃油供给量。在恒压状态下,燃油供给量与电磁阀的开启时间成正比,因此与发动机或油泵的转速(以时间为计量的燃油喷射)无关。

(4) 液压辅助动力

与传统燃油喷射系统相比,将压力的产生与燃油的喷射分离开来,有利于燃烧室的充分燃烧。燃油喷射压力在系统中基本可以自主选择。目前最高燃油压力为1600巴,将来会达到1800巴。

共轨系统通过引入预喷射或多次喷射可以进一步减少废气排放,也能明显降低燃烧噪声。通过多次触发高速转换阀的开闭可以在每个喷射周期内实现多达5次的喷射。喷油针阀的开闭动作是液压辅助元件助力的,以保证喷射结束的快速性。

(5) 控制和调节

发动机的控制单元通过传感器检测加速踏板的位置以及发动机和车辆的当前工况。采集到的数据包括:

① 曲轴转速和转角; ② 燃油轨道的压力; ③ 进气压力;

④ 进气温度、冷却液温度和燃油温度; ⑤ 进气量; ⑥ 车速等。

电控单元处理输入信号。与燃烧同步,电控单元计算施加给压力控制阀或计算模块、喷油器和其他执行机构(如EGR阀,废气涡轮增压器)的触发信号。

喷油器的开关时间应很短,采用优化的高压开关阀和专业的控制系统即可实现。

根据曲轴和凸轮轴传感器的数据,对照发动机状态(时间控制),角度/时间系统调节喷油正时。电控柴油机系统(EDC)可以实现对燃油喷射量的精确计算。此外,EDC还拥有额外的功能以进一步提高发动机的响应特性和便利性。

其基本功能包括对柴油燃油喷射正时的精确控制,和在给定压力下对油量的控制。这样,它们就保证了柴油发动机具有能耗低、运行平稳的特点。

其他开环和闭环控制功能用于减少废气排放和燃油消耗,或提供附加的可靠性和便利性,具体例子有:

① 废气在循环控制; ② 增压控制; ③ 巡航控制;

④ 电子防盗控制系统等。 (6) 控制单元结构。

由于发动机控制单元通常最多有8个喷油器输出口,所以超过八缸的发动机需要两个控制单元。它们通过内置高速CAN网络的“主/从”接口进行连接,因此也拥有较高的微控制器处理能力。一些功能被 分配给某个特定的控制单元(如燃料平衡控制),其功能根据需求情况(如检测传感器信号)可以动态地分配给一个或多个控制单元。

The Common Rail Calls for lower fuel consumption, reduced exhaust-gas emiion, and quiet engines are making greater demands on the engine and fuel-injection system.The demands placed on diesel-engine fuel-injection systems are continuously increasing.Higher preures, faster switching times, and a variable rate-of-discharge curve modified to the engine operating state have made the diesel engine economical, clean, and powerful.As a result, diesel engines have even entered the realm of luxury-performance sedans.These demands can only be met by a fuel-injection preure.At the same time the injected fuel quantity must be very precisely metered, and the rate-of-discharge curve must have an exact shape, and pre-injection and secondary injection must be performable.A system that meets these demands is the common-rail fuel-injection system.The main advantage of the common-rail system is its ability to vary injection preure and timing over a broad scale.This was achieved by separating preure generation (in the high-preure pump) from the fuel-injection system (injection).The rail here acts as a preure accumulator.Principle of the Common Rail The common-rail system consists of the following main component groups: ① The low-preure stage, comprising the fuel-supply system components; ② The high-preure system, comprising components such as the high-preure pump, fuel-rail, injector, and high-preure fuel lines.The electronic diesel control (EDC), consisting of system modules, such as sensors, the electronic control unit, and actuators.The key components of the common-rail system are the injectors.They are fitted with a rapid-action valve (solenoid valve or piezo-triggered actuator) which opens and closes the nozzle.This permits control of the injection proce for each cylinder.All the injectors are fed by a common fuel rail, this being the origin of the term “common rail”.In the common-rail fuel-injection system, the function of preure generation and fuel injection are separate.The injection preure is generated independent of the engine speed and the injected fuel quantity.The electronic diesel control (EDC) controls each of the components.(1) Preure Generation.Preure generation and fuel injection are separated by means of an accumulator volume.Fuel under preure is supplied to the accumulator volume of the common

rail ready for injection.A continuously operating high-preure pump driven by the engine produces the desired injection preure.Preure in the fuel rail is maintained irrespective of engine speed or injected fuel quantity.Owing to the almost uniform injection pattern, the high-preure pump design can be much smaller and its drive-system torque can be lower than conventional fuel-injection systems.This results in a much lower load on the pump drive.The high-preure pump is a radial-piston pump.On commercial vehicles, an in-line fuel-injection pump is sometimes fitted.(2) Preure Control The preure control method applied is largely dependent on the system.One way of controlling rail preure is to control the high-preure side by a preure-control valve.Fuel not required for injection flows back to the low-preure circuit via the preure-control valve.This type of control loop allows rail preure to react rapidly to changes in operating point ( e.g.in the event of load changes ) .Control on the high-preure side was adopted on the first common-rail systems.The preure-control valve is mounted preferably on the fuel rail.In some applications, however, it is mounted directly on the high-preure pump.Another way of controlling rail preure is to control fuel delivery on the suction side.The metering unit flanged on the high-preure pump makes sure that the pump delivers exactly the right quantity of fuel rail in order to maintain the injection preure required by the system.In a fault situation, the preure-relief valve prevents rail preure from exceeding a maximum.Fuel-delivery control on the suction side reduces the quantity of fuel under high preure and lowers the power input of the pump.This has a positive impact on fuel consumption.At the same time, the temperature of the fuel flowing back to the fuel tank is reduced in contrast to the control method on the high-preure side.The two-actuator system is also a way of controlling rail preure, which combines preure control on the suction side via the metering unit and control on the high-preure side via the preure-control valve, thus marrying the advantages of high-preure-side control and suction-side fuel-delivery control.(3) Fuel Injection.The injectors spray fuel directly into the engine’s combustion chambers.They are supplied by short high-preure fuel lines connected to the fuel rail.The engine control unit controls the switching valve integrated in the injector to open and close

the injector nozzle.The injector opening times and system preure determine the quantity of fuel delivered.At a constant preure, the fuel quantity delivered is proportional to the switching time of the solenoid valve.This is, therefore, independent of engine or pump speed( time-based fuel injection ).(4) Potential Hydraulic Power.Separating the functions of preure generation and fuel injection opens up future degrees of freedom in the combustion proce compared with conventional fuel-injection systems; the injection preure at preure at present is 160 MPa; in future this will rise to 180 MPa.The common-rail system allows a future reduction in exhaust-gas emiions by introducing pre-injection events or multiple injection events and also attenuating combustion noise significantly.Multiple injection events of up to five per injection cycle can be generated by triggering the highly rapid-action switching valve several times.The nozzle-needle closing action is hydraulically aisted to ensure that the end of injection is rapid.(5) Control and Regulation.The engine control unit detects the accelerator-pedal position and the current operating states of the engine and vehicle by means of sensors.The data collected includes:

① Crankshaft speed and angle; ② Fuel-rail preure; ③ Charge-air preure:

④ Intake air, coolant temperature, and fuel temperature: ⑤ Air-ma intake: ⑥ Road speed, etc.The electronic control unit evaluates the input signals.In sync with combustion, it calculates the triggering signals for the preure-control valve or the metering unit, the injectors, and the other actuators ( e.g.the EGR valve, exhaust-gas turbocharger actuators, etc.).The injector switching times, which need to be short, are achievable using the optimized high-preure switching valves and a special control system.The angle/time system compares injection timing, based on data from the crankshaft and camshaft sensors, with the engine state ( time control ).The electronic diesel control (EDC) permits a precise metering of the injected fuel quantity.In

addition, EDC offers the potential for additional functions that can improve engine response and convenience.The basic functions involve the precise control of diesel-fuel injection timing and fuel quantity at the reference preure.In this way, they ensure that the diesel engine has low consumption and smooth running characteristics.Additional open-and close-loop control functions perform the tasks of reducing exhaust-gas emiions and fuel consumption, or providing added safely and convenience.Some examples are:

① Control of exhaust-gas recirculation; ② Boost-preure control; ③ Cruise control;

④ Electronic immobilizer, etc.(6) Control Unit Configuration.As the engine control unit normally has a maximum of only eight output stages for the injectors, engines with more than eight cylinders are fitted with two engine control units.They are coupled within the “ master/slave ” network via an internal, high-speed CAN interface.As a result, there is also a high microcontroller proceing capacity available.Some functions are permanently allocated to a specific control unit ( e.g.fuel-balancing control ).Other can be dynamically allocated to one or many of the control units as situation demand ( e.g.to detect sensor signals ).

推荐第2篇:中英文对照

Text5_EN

I don\'t know why I overlooked that problem.

I haven\'t overlooked Chinese achievements in science.Sometimes you are too frank.

High birthrates cannot be changed overnight.

That book only told a pack of lies.

They searched my room and found nothing.

When it rained people in that small town had to stay in the house.

推荐第3篇:中英文对照

中英文对照

金融危机下企业财务风险产生的原因及防范分析

财务风险管理

财会研究 金融危机下企业财务风险产生的原因 及防范分析 上

海理工大学管理学院 叶建波

[ 摘 要 ]08 年金融危机的爆发给我国企业带来了严重的影响 , 许多 企业由 于没 有做 好充 分的防 御准 备而 导致 企业财 务风 险的发生,面对危机,怎么样做好企业财务风险防范,是当前企业面临的首要问题,也是以后企业管理的重点。

[ 关键词 ] 信用风险 内部监控 激励机制 08 年金融 危机 给全 球经 济带来 了 严 重 的 影 响 , 我 国 企 业 在 金 融 危 机 下 ,也 普 遍 产 生 了 程 度 不 一 的 财 务 风 险 ,这 与 我 国 企 业 历 来 欠 缺 财务风险意识,缺乏有效的内部管理控制体系密切相关。 我国企业产生财务风险主要有以下几个原因 : 财务监控制度对企业财务管 理的 成功 起着关 键的 作用 。 在我 国,内部 财务监控制度的不健全和财务关系的混乱是产生企业财务风险的重 要因素之一。 与国外发达国 家相 比,我国 内部 财务 监控 制度的 普及 率 还较低。 即使有的企业有,也不能严格执行,由于管理体制的不完善和 缺乏有效的约束机制,导致企业的财务风险极易发生。 1. 企业财务管理系统不能适应外部复杂多边的宏观环境 随着全球经济一体化的 深入 发展 ,我国 企业的 财务 活动 也处 在了 全球的行业经济链之中,企业的财 务管 理的环 境由 此变 得更 加复杂 多 变 ,外 部 环 境 变 化 在 为 企 业 带 来 机 会 和 利 益 的 同 时 ,也 导 致 企 业 面 临 着各种风险,甚至是威胁,如全球 的宏观 经济 形势 变化、我国国 民经 济 整体形势变化、所在行业的政策变化、行业 景气 度、国 家信贷 以及 外汇 政策 的 调 整、银 行 利 率 的 变 化、外 汇 汇 率 的 波 动、通 货 膨 胀 程 度 等 等 。 这些因素存在于企业之外, 其变化 也是 企业 难以 预见和 难以 改变 的, 这就势必影响到企业的财务活动, 如利率的变动必然会产生利率风 险 ,包 括 支 付 的 利 息 过 多 的 风 险、产 生 利 息 的 投 资 发 生 亏 损 的 风 险 和 不能履行偿债义务的风险等;汇 率的 变动 则会直 接影 响到 我国 进出口 产品 的成 本, 人 民币升 值会 提高 我国 出口产 品的 成本 ,对出 口企 业 不 利,因而会影响我国外贸出口,从而 会减少 外贸 顺差 。 反之 ,则会提 高 进口产品成本,对进口企业不利。 而通货膨胀,将使企业资金供给持续 发生短缺,货币性资金持续贬值,实 物性 资金相 对升 值,垫 付成 本持续 升高。 宏观环境的不利变化给企 业带 来财务 风险 是实 实在 在的,轻 者 不能实现预期收益,重者血本无归。 4. 信用风险薄弱,应收账款拖欠严重 企业客户包括供应方和购买方, 企业的信用风险因客户性质的 不同也体现在两个方面。 在 现代 社会 ,市场 的竞争 机制 发挥 着重 要的 作用,要想扩大市场占有率,企 业不 仅要 生产出 合格 的产 品,还 要控制 好产品的成本和价格,同时必须巧妙合理的运用好信用促销。 但是,一 些 企 业 为 了 扩 大 销 售 量 和 销 售 额 ,盲 目 的 运 用 赊 销 策 略 ,忽 视 了 对 客 户的还款能力和资信水平的调 查, 最 终导致 企业 的应 收账 款增加 ,收 款风险增大情况的出现,最后蒙受风险和损失的还是企业自己 。 所以, 企 业 需 要 根 据 客 户 的 情 况 ,制 定 一 套 信 用 判 定 标 准 ,根 据 判 定 的 客 户 信用情况来判别是否该赊销产品。 加强对财务风险的防范,企业须做好以下几点: 1. 建立财务风险预警系统 (1 )加强信息管理 首 先 建 立 财 务 预 警 管 理 组 织 机 构 ,并 遵 循 “专 人 负 责、职 责 独 立 ” 的 原 则 ,确 保 财 务 预 警 分 析 的 工 作 能 够 有 专 人 落 实 ,且 不 受 其 他 组 织 机构的干扰和影响。 而且财 务风 险预 警系 统应该 是开 放性 的,不 仅包 括内部财务信息,还包括外部相关信息。 最为关键的是,系统信息要不 断更新,资料系统要不断升级 ,确保 财务 信息的 及时 性、准 确性 和有效 性。 (2 )健

全财务风险缝隙与处理机制 财务预警系统的关键和核心是高效率的财务风险分析方法 。 处理 财务风险的方法主要包括应急措施、补救方法和改进方案这三点。 (3 )建立财务风险预警的计算机辅助管理系统 由于工作量大与繁杂以 及要 求严 格的 原因,财 务风 险预 警系 统的 构 建 和 运 行 应 实 施 微 机 化 管 理 ,并 与 会 计 核 算 软 件 衔 接 ,进 行 动 态 监 督,减少数据采集、输入过程中的错误,保证信息质量。 (4 )加强人才培训,注重人才更新 人才的培养是企业发展 的核 心,企 业一 定要培 养一 批高 素质 的财 2. 资本结构不合理,资产流动性差 企业资金结构主要是指企业权益资金与负债资金以及固定资本 与流动资本的比例关系。 企业如果 出现 投资与 筹资 决策 的失 误,就会 导致企业的资本结构不合理,会 出现 负债比 例过 高,而 流动 资金少、资 金链断裂的现象。 企业债务比例高的直接后果就是使得企业不能到期 及时清还债务,陷入财务困境 之中 。 高负 债率当 然还 给企 业带 来高的 清还利息的压力,即债务成本,如 果企 业经营 不善 ,就会 导致 企业出 现 资不抵债,面临破产的危险。 因此,企业在融资时必须考虑到后续的还 债 能 力 ,否 则 ,会 因 为 流 动 资 金 不 足 和 变 现 能 力 不 强 而 导 致 财 务 风 险 的发生,最终导致企业破产的悲剧。 3. 企业财务内部监控制度不健全 内部财务监控制度作为 企业 财务 活动 中自我 调节、自我 约束 的内 在机制,在企业管理系统中具有举 足轻 重的作 用。 及 时建 立企 业内部 财会研究 注 册 会 计 师 的 审 计 质 量 ,能 够 保 证 公 司 合 理、有 效 的 运 用 会 计 政 策 的 选择。 同时,在法律上增强注册会计师的审计效力 ,更加确保公司的外 部约束机制。 1、健全相关法律法规 完善资本市场法制建设 ,通过 政策 法制 方面来 减少 会计 利润 的操 纵,我国颁布的《证券法》标志着 我国 市场 步入依 法治 市进 入的 崭新阶 段 ,但 是 资 本 市 场 的 法 制 建 设 还 有 待 完 善 ,应 出 台 更 加 具 体 的 法 律 约 束力的法律法规,规范我国的资本 市场的 行为 。 完善 会计 制度和 会计 准则 ,我 国 颁 布 的 《公 司 会 计 准 则 》是 一 个 更 加 完 善 的 会 计 法 规 ,但 仍 存在一定的局限性,会计政策选 择的主 体仍 然可 以利 用机会 谋求 自身 利益。 会计政策的制定机构应不断 完善 会计 政策 ,尽可能 减少 会计 政 策选择的空间。 6、加强经理人自身素质的培养 经理人是会计利润的操 纵者 ,经常 安排 他们参 见与 公司 经营 相关 的学习、培训等,能够提高经理 人自 身素 质和修 养,培 养管 理者 的战略 眼光和全局意识。 在实际的 经营 管理 过程中 ,更加 自觉 的按 照会计 准 则等规定进行管理,更多考虑公司整体的利益。 2、完善公司绩效考评体系 公司内部对管理人员的绩效考评主要以财务报表报出的数据为 依据,这种考评体系存在一定的局 限性 。 公司内 部应 改善 对经 理人的 绩效考评体系,建立一套科学、规 范的、以公司 价值 为导 向的 考核与 评 价体系,全方位考察管理人员的经 营效率 。 该体 系应 该具 有较强 的综 合性和操作性,能够灵活的、准确的对经理人的绩效进行考评 。

四、结语 综上所述, 文章首 先探讨 了公 司会 计政 策选择 的定 义及 必要 性, 接着分析影响公司价值的会计 政策 选择 的重要 因素 ,最后 探讨 了规范 会计政策选择的相关对策。 在现 实生 活中,相 信随 着我 国市 场经济 的 发 展 和 市 场 经 济 制 度 的 健 全 ,随 着 法 律 监 督 能 力 不 断 增 强 ,公 司 的 会 计政策选择将越来越规范。 3、健全的激励机制 经理人是会计利润操纵 的实 施者 ,公司 对经理 人从 物质 和精 神两 方面进行合适的奖励,有利于经理 人更 加自觉 的按 照会 计准 则进行 经 营管理,采取符合股东最大利益的行为。 同时,通过各种途径引导投资 者由追求会计利润最大化转移到追求公司价值最大化的轨道上来 。

Analysis of the causes and prevention of corporate financial risk in the financial crisis Financial Risk Management Accounting research on corporate financial risk analysis of the causes and prevention of financial crisis Sea University School of Management Ye Jianbo

[Abstract] 2008 financial crisis, China's enterprises to bring a serious impact on many companies did not make enough defensive preparations lead to the risk of corporate finance, in the face of the crisis, Zenmeyangzuo corporate financial risk enterprises are facing the most important iue, but also the future of enterprise management focus.

[Key words] credit risk internal control incentives in 2008 financial crisis has serious implications to the global economy, China's enterprises in the financial crisis, are generally produced with varying degrees of financial risk, China's enterprises has always been the lack of financial risk awarene, lack of effective internal management control system are closely related.China's enterprises generate financial risk for several reasons: the succe of the financial control system of financial management plays a key role.In China, the internal financial control system is not perfect and the chaos of the financial relationship is an important factor in a corporate financial risk.Compared with developed countries, the penetration rate of China's internal financial control system is still relatively low.Some companies can not be strictly enforced, due to the imperfections of the management system and the lack of effective restraint mechanism, leading to financial risk can easily occur.A.Enterprise financial management system can not adapt to the external complex multilateral macro-environment in-depth development of the global economic integration, the financial activities of our enterprise in the economic chain of the global industry, the financial management of the environment thus become more complex and volatile external environment, changes in busine opportunities and benefits at the same time, also led to the enterprises are faced with various risks, or even a threat, such as the global macroeconomic situation changes, changes in the situation of China's national economy as a whole, the industry's policy changes in the industry boom, the adjustment of the national credit and foreign exchange policy, changes in bank interest rates, foreign currency exchange rate fluctuations, inflation, the degree and so on.These factors exist outside the firm, the change is also difficult to predict and difficult to change, which is bound to affect the financial activities of enterprises, such as changes in interest rates would have interest rate risk, including the risk of exceive interest payments, resulting in interest the risk of lo and can not meet their debt obligations, risks of the investment; movements in exchange rates will directly affect the cost of China's import and export products, the appreciation of the renminbi will increase the cost of China's export products, export enterprises, which will affect ourexports, which will reduce the trade surplus.On the contrary, it will increase the cost of imported products, unfavorable import busine.Inflation, will enable the enterprise money supply, the continuing shortage of monetary funds continued to depreciate relative appreciation of the in-kind funds, to advance the cost continues to rise.Adverse changes in the macroeconomic environment to the enterprise financial risk is real, the light can not achieve the expected benefits and weight who lose everything.4.Weak credit risk in accounts receivable owed

to a serious enterprise customers, including supply-side and buy side, the credit risk of customers to the different nature is also reflected in two aspects.In modern society, the competition in the market mechanism to play an important role, in order to increase their market share, enterprises not only to produce qualified products, but also to control the cost and price of a good product, at the same time need to be smart and reasonable use of a good credit promotions.However, some companies in order to expand sales volume and sales, the blind use of credit strategy, ignoring the investigation of the customer's repayment ability and creditworthine, eventually leading to an increase in the receivables, receivables increased risk of happening Finally, at risk and the lo of the enterprise.Therefore, companies need customers to develop a set of credit criteria, to determine the customer credit situation to determine whether the credit products.Strengthen the prevention of financial risks, companies should take the following points: 1.Financial risk early warning system (1) first establish financial early warning management organizations to strengthen information management, and follow the principles of the person responsible, responsibility and independence, "to ensure that the analysis of the financial early warning to staff in implementing, and not subject to interference from other organizationsand impact.And financial risk early warning system should be open, including not only the internal financial information, including external information.The most critical system information to continuously update information systems to constantly upgrade, to ensure the timeline, accuracy and effectivene of the financial information.(2) the key and core of the gap of a sound financial risk and the mechanism for handling financial early warning system of efficient financial risk analysis.The handling of financial risks including emergency measures to remedy and improve the programs these three points.(3) the establishment of computer-aided management of financial risk early warning system due to heavy workload and complicated and demanding of reasons, financial risk early warning system construction and operation should implement a computerized management, and convergence with the accounting software, dynamic supervision, to reduce data collection, errors in the input proce, to ensure the quality of the information.(4) To strengthen personnel training, and focus on talent and update personnel training is the core of enterprise development, companies must develop a number of high-quality fiscal.The capital structure is irrational, the liquidity difference between corporate capital structure refers to the proportion of corporate equity capital and debt capital and fixed capital and working capital relations.If the investment and financing decision-making mistakes, will lead to capital structure is unreasonable, the debt ratio is too high, le liquidity, funding strand breaks phenomenon.A high proportion of corporate debt is a direct consequence makes the companies can not due to the timely discharge of debts, being in financial trouble.The high debt ratio, of course, returned to the enterprise to bring the preure of the high clear interest, namely, the cost of debt, if busine is poor, it will lead to enterprises insolvent and facing the risk of bankruptcy.Therefore, the financing must take into account the subsequent ability to repay debt, otherwise, because of the lack of liquidity and liquidity is not strong, which led to the occurrence of financial risk, and eventually led to the tragedy of corporate bankruptcies.3.Corporate financial internal control system is not perfect, self-regulation of internal financial control systems as a corporate finance activities, the

internal mechanism of self-restraint, has a pivotal role in the enterprise management system.The timely establishment of the internal accounting of Certified Public Accountants of audit quality, to ensure that the company is reasonable, effective use of the accounting policy choices.At the same time in the law to enhance the effectivene of the Certified Public Accountant audit, and more to ensure that the external constraint mechanism., Improve relevant laws and regulations to improve the capital market and legal system, through the policy of the rule of law to reduce the manipulation of accounting profits, China promulgated the "Securities Act" indicates that China market entered a new stage of their law to enter, but the legal construction of the capital market should be improved, the introduction of more specific legally binding laws and regulations to regulate the behavior of China's capital market.Improve the accounting system and accounting standards, China promulgated the "Accounting Standards" is a more complete accounting regulations, but there are still some limitations, the main body of accounting policy choices can still take advantage of opportunities to pursue their own interests.Accounting policy-making institutions should continue to improve the accounting policies, to minimize the space of accounting policy choice.Train managers to strengthen the quality of the manager is the accounting profit of the manipulator, often arranged they see related to the company's learning, training, etc., can improve the quality of managers and self-cultivation, and to train the managers of the strategic vision and global awarene .The actual management proce more consciously in accordance with the provisions of the Accounting Standards and other management to give more consideration to the interests of the company as a whole.2, and improve company performance appraisal system within the company management performance evaluation based on the financial statements reported data, this evaluation system has some limitations.Within the company should improve its performance appraisal system for managers, to establish a scientific, standardized to the value of the company-oriented aement and evaluation system, a full range of inspection management of operational efficiency.The system should have a strong and operational flexibility, accurate evaluation of the performance of the manager.Conclusion In summary, the article first discues the definition and neceity of the company's accounting policy choices, and then analyze the important factors affect the value of the company's accounting policy choices, and finally discues the related countermeasures to standardize the accounting policy choices.In real life, I believe that with the development of China's market economy and the integrity of the system of market economy, as the legal supervision and increased the capacity, the company's accounting policy choices will be more and more standardized.3, a sound incentive manager is the manipulation of accounting profits implementers, managers from both material and spiritual appropriate incentives, managers more conscious management, in accordance with the accounting standards to take the best interests of the Shareholders behaviors.At the same time, to guide investors through various means and transferred to the pursuit of accounting profits to maximize the pursuit of the company to maximize the value of the track up.

推荐第4篇:中英文对照

AEROFLEX “亚罗弗”保温 ALCO “艾科”自控 Alerton 雅利顿空调 Alfa laval阿法拉伐换热器 ARMSTRONG “阿姆斯壮”保温 AUX 奥克斯

BELIMO 瑞士“搏力谋”阀门 BERONOR西班牙“北诺尔”电加热器 BILTUR 意大利“百得”燃烧器 BOSIC “柏诚”自控 BROAD 远大

Burnham美国“博恩汉”锅炉 CALPEDA意大利“科沛达”水泵 CARLY 法国“嘉利”制冷配件 Carrier 开利 Chigo 志高

Cipriani 意大利斯普莱力

CLIMAVENETA意大利“克莱门特” Copeland“谷轮”压缩机 CYRUS意大利”赛诺思”自控 DAIKIN 大金空调

丹佛斯自控 Dorin “多菱”压缩机

DUNHAM-BUSH 顿汉布什空调制冷 DuPont美国“杜邦”制冷剂 Dwyer 美国德威尔 EBM “依必安”风机

ELIWELL意大利“伊力威”自控 Enfinilan 英国“英菲尼兰“阀门 EVAPCO美国“益美高”冷却设备 EVERY CONTROL意大利“美控” Erie 怡日

FRASCOLD 意大利“富士豪”压缩机 FRICO瑞典“弗瑞克”空气幕 FUJI “富士”变频器

FULTON 美国“富尔顿”锅炉 GENUIN “正野”风机 GREE 格力

GREENCOOL格林柯尔 GRUNDFOS “格兰富”水泵 Haier 海尔 Hisense 海信 HITACHI 日立

霍尼韦尔自控 Johnson 江森自控 Kelon 科龙

KRUGER瑞士“科禄格”风机 KU BA德国“库宝”冷风机 Liang Chi 良机冷却塔 LIEBERT 力博特空调 MARLEY “马利”冷却塔 Maneurop法国“美优乐”压缩机 McQuary 麦克维尔 Midea 美的 MITSUBISHI三菱

Munters 瑞典“蒙特”除湿机 Panasonic 松下 RANCO “宏高”自控

REFCOMP意大利“莱富康”压缩机 RIDGID 美国“里奇”工具 RUUD美国“路德”空调 RYODEN “菱电”冷却塔 SanKen “三垦”变频器 Samsung 三星 SANYO 三洋

ASWELL英国森威尔自控 Schneider 施耐德电气 SenseAir 瑞典“森尔”传感器 SIEMENS 西门子

SINKO \",28商机网;新晃“空调 SINRO “新菱”冷却塔 STAND “思探得”加湿器 SWEP 舒瑞普换热器 TECKA “台佳”空调 Tecumseh“泰康”压缩机 TRANE 特灵

TROX德国“妥思”风阀 VASALA芬兰“维萨拉”传感器 WILO德国“威乐”水泵 WITTLER 德国”威特”阀门 YORK 约克

ZENNER德国“真兰”计量

推荐第5篇:中英文对照

医院中英文对照

发热门诊Have Fever主治医师Doctor-in-charge 供应室Supply Room谢绝入内No entering 红灯亮时谢绝入内No entering when red light

彩超、心电图Colorful Cardiogram/ECG住院楼Inpatient Building 透析血磁EndoscopeDept.护士Nueser康复理疗科RehabilitationPhysiotherapyDept.

中药计价China medical price account肛肠科Ano-proctology

皮肤、肛肠、男性科、泌尿科候诊Dermatology、Ano-proctology、male Urology Clinic 皮肤科、肛肠科、男性科、泌尿科Dermatology、Ano-proctology、male Urology Dept 中医科Traditional Chinese Medicine五官科ENT Dept.男性科、泌尿科 Male urology Dept.安全出口Exit

预防保健科Medical center for health preventionand care

后勤科、药库Logistic Room、Seore入院登记In-patient Admion 高压氧治疗Hyperbaric Oxygehation Therapy碎石中心ESWL Center 急救中心Emergency Center挂号收费Registration

中心药房Cenreral Pharmacy内科门诊Internal Medicine Clinic会议室Meeting Room手外科Hand Surgery 产科Obstentrics Dept.骨外科Orthopedics Dept.神经、烧伤外科Neurosurgery.Plaseric surgey Dept.

麻醉科Anaesthesiology手术室Operation Room 泌尿、肿瘤外科Urologic.Gumorsurgery Dept.妇科Gynecology Dept.内二科Internal Medicine.Ward 2产房及爱婴中心Delivery Room内一科Internal Medicine.Ward 1洗手间Toilet

普外、胸外科Surgey、Thoracic Surgey Dept.皮肤科Dermatology Dept.中医骨伤科Traditional Mediaine or Thopaedics餐厅Dining Room 配餐室Pantry Room后勤科Logistics Dept.电工室Electrician Room接待室Dermatology Room 内、儿科候诊 Internal medicine.Pediatrics功能检查候诊Function Exam 中医科候诊TCM Clinic放射科候诊Radiology Clinic 妇科门诊Gynecology Dept.产科候诊Obstentrics Clinic 肛肠科候诊Ano-proctology妇科候诊Gynecology Clinic 产科门诊Obstentrics Dept.五官科候诊ENT.Clinic 外科候诊Surgery Clinic输液中心Transfusion Center 皮肤、泌尿科候诊 Dermatology.Male Urology Clinic检验候诊Clinical Laborotories 家属休息Relation Rest Room口腔科门诊Stomatology Clinic 内儿科Internal Medicine.Pediaarics镜检科Endoscope Dept.外科Surgrey Dept.检验中心Laboratory Center 功能检查Function Exam Dept.登记处Registration 预防保健门诊Hygine & Public Health Dept.收费处Cashier 美容科、镜检科门诊 Cosmetology Dept.Endoscope Clinic

收费健康发证Gharge lue Bill of Health试敏观察室Scratch Espial Room

推荐第6篇:中英文对照A

《美国口语惯用法例句集粹》A

A (Page 1-4)

1.about

1)

2)

3)

4)

5)

6)

7) I\'d like to know what this is all about.我想知道这到底是怎么回事。How about a fish sandwich? 来一块鱼肉三明治怎么样?What about me? 我怎么样?I\'m not about to go in that old house.我是不会进那幢旧房子的! Yes I remember that night.What about it? 是的,我记得那个晚上,那又怎样?What\'s this all about? 这到底是怎么回事?It\'s about time you showed up! 差不多是你该露面的时候了。

2.above

1)

2) Above all, I want everything quiet.首要的是:我要一切保持安定。Tom thinks he\'s above hard work.汤姆认为自己没必要努力工作。

3.act

1)

2)

3)

4)

5)

6) Would you please act out what happened? 你能把发生的事演示一下吗?Watch Ricky.He sometimes likes to act up in cla.注意里基,他又是喜欢在课堂上捣蛋。That profane comedian needs to clean up his act.那个爱说粗言秽语的喜剧演员应该净化一下自己的言行。We need to get our act together and come to see you.我们需要统一意见后来见你。The newspapers called the earthquake an act of God.报纸上称那次地震为天灾。 Masa is a cla act.玛莎是位杰出的女性。

4.action

1)

2)

3)

4) We\'re going to bring action against our debtors.我们打算控告我们的债务人。 Did you see any action in yesterday\'s ballgame? 昨晚的棒球比赛中你看到有什么有趣的精彩场面吗?Our community is going to take action against the proposed waste dump.我地区要采取行动反对那项垃圾处理场的提案。Jim wants to go where the action is.吉姆想去有刺激性的地方。

5.advantage

1)

2) Our opponents have a height advantage on us.我们的对手在身高上比我们占有优势。 Nobody likes to be taken advantage of.没有人喜欢被捉弄(或:被欺骗、利用)

6.after

1)

2)

3)

4) I think that girl is after you.我想那女孩是在追你。 It looks like things are gonna work out after all.看起来事情终会解决的。This soft drink has a nasty aftertaste.这软饮料有种让人难受的余味。I see your point, but don\'t you think it\'s way after the fact.我明白你的意思,但你不觉

得这已是“事后诸葛亮”了吗?

7.again

1) I could go to Japan again and again.我可以一而再、再而三地去日本。(注:意指不会感到

厌倦)

8.age

1)

2) Would you please act your age! 请你做事要有一个与自己年龄相称的样子。 This is a \"coming of age\" movie.这是一部成人影片。

9.air

1)

2)

3)

4)

5)

6)

7)

8)

9) I need to go outside and get some air.我需要出去呼吸点新鲜空气。I don\'t know what\'s wrong, but can feel it in the air.虽然我不知道到底是出了什么差错,但我能隐隐约约感觉到。Mike was sad when they took his favorite program off the air.当迈克喜欢的节目被取消时,他感到很伤心。The sale of our house is still up in the air.我们的房子出勤率售一事还没有最后定下来。After winning the championship, I felt I could walk on air.获得冠军后,我飘飘欲仙。Your sister is such an airhead.你姐姐真是来个没有头脑的人。Janet Jackson\'s new song is getting lots of airplay.珍妮〃杰克逊的新歌到处都在不断地播放。That last time I took a plane, I got airsick.上次我乘飞机时晕机了。I hope there\'s no bad air between us.我希望我们之间的关系不要很别扭。

10.all

1)

2)

3)

4)

5)

6)

7)

8)

9)

10)

11)

12)

13) It\'s looks like we won\'t be going after all.看起来最后我们还是不能去。We\'ve all but finished the project.我们已几乎完成了那个项目。All in all I\'d say it\'s been a very productive day.总的来说,我认为这一天过得很充实。Let\'s go all-out and win this game! 让我们尽全力来打赢这场比赛。We knew it was all over when we saw the building burst.当我们看见那座建筑突然起火时,我们知道一切全完了。We wish you all the best.我们大家祝福你一切如意。If it\'s all the same to you, I\'d just as soon not go.如果这对你都是一回事的话,我就不想去了。They were running from the police like all get-out.他们以极快的速度逃脱警察的追赶。I didn\'t see them come in at all.我根本高没有发现他们的进来。Let\'s settle this matter once and for all.让我们来把这个问题一次性地彻底解决掉。Mark is an all-around athlete.马克是一个全能运动员。Did you get to play in the all-star game? 你入选全明星队的比赛了吗?He bloke the all-time record in the 100-meter run at his school.他打破了他所在的学校

100米跑的历史最高记录。

11.alley

1) Working on cars isn\'t up my alley.修理汽车不是我拿手的活儿。

12.alone

1)

2) I just wanna be left alone.我只是想一个人呆会儿。Can\'t you just leave well enough alone? 你不能少管一些闲事吗?

13.along

1)

2) You knew all along what was going on.你从一开始就知道所发生的事。 Debbie doesn\'t get along with Steve.戴比和史蒂夫相处得不好。

1)

2)

3)

4)

5) Mr.Pak came here searching for the American dream.帕克先生来到这儿寻求他的“美国梦”。Some foreigners become Americanized while living in the U.S.一些外国人在美国居住时被美国化了。Not having any job freedom would be totally unAmerican.没有选择职业的自由是完全违背美国精神传统的。Bill is an all-American quarterback.比尔是全美(橄榄球)明星赛的四分卫队员。I just can\'t go on the American way.我无法适应美国方式。

15.animal

1)

2) Water-skiing really brings out the animal in Tom.滑水运动真正激发出了汤姆的活力与激情。The young actor emits a lot of animal magnetism on the screen.那个年轻演员在荧幕

上充分显示出他的性魅力。

16.answer

1) I called Emi but there was no answer.我给埃米打了电话,但是没人接。

17.apple

1)

2)

3)

4)

5) Have you ever been to the Big Apple? 你去过纽约吗?Do I sense an apple of discord between you two? 你问我有没有感觉出你们两人之间的不和,是吗?Heather is the apple of my eye.希瑟是我的掌上明珠。Rita likes to keep everything in apple-pie order.丽塔喜欢把一切都弄得井井有条。Dennis has always been an apple polisher.丹尼斯一直就是一个马屁精。

18.arm

1)

2)

3)

4) You don\'t have to twist my arm to get me to go with you.用不着你强迫我跟你走。My father is a hopele armchair quarterback.我爸爸是一个没救了的纸上谈兵的人。The suspects are armed and dangerous.嫌疑犯带有武器,十分危险。Every spring the park is filled with lovers walking arm in arm.每到春天公园里到处都是

手挽手散步的恋人。

19.around

1)

2) Coach Johnson has been around for 30 years.约翰逊教练已有三十年的经验了。Someone is on duty here around-the-clock.有人在这里昼夜值班。

20.as

1)

2)

3)

4)

5)

6) It looks as if someone has already been here.看起来在人来过这里了。As for me, I\'m going home.至于我,我准备回家。Marty is acting as if nothing happened.马蒂表现得像什么也没发生过一样。I want this room left as is.我希望这间房子保持原样。The changes will begin taking place as of tomorrow.变动从明天开始实施。Police are baffled as to the whereabouts of the kidnappers.警察局搜寻绑架者的工作受

挫。

1)

2)

3)

4) Our gas bill average about $50 a month.我们每个月的煤气费平均50美元。On the average, I\'d say we eat chicken once a week.我们平均每周吃一次鸡肉。Kent describes himself as just an average Joe.肯特视自己为一名普通的美国人。On the average day, over 100,000 kids bring guns to school in the U.S.在美国平常日

子里,有100,000个孩子带手枪去上学。

22.away

1)

2)

3)

4)

5) What makes you think you\'re gonna get away with this? 是什么使你认为你可以免受处罚?I wish they\'d do away with these complicated tax forms.我希望他们能费除掉这些复杂的税务表格。We\'re planning a weekend getaway for our anniversary.我们正在为庆祝我们的纪念日而安排一次周末的外出活动。Tom wants to run away from home.汤姆想从家里出逃。 Dave and Kathy are going to steal away on vacation.戴夫和凯茜计划在假期里偷偷跑出

去。

推荐第7篇:中英文辞职报告

背景:Harrod 当过十八个月的推销员。他虽然很喜欢同各地销售商打交道,单却不愿经常出差。他把这个问题向销售经理放映过几次,可公司并没有其他适合他的职位,所以他只好辞职。

Dear Benson:

I am sure it will come as no surprise to you that I wish to resign my position as a sales representative , effective at your convenience ,but not later than June 12.

You are fully aware of my problem, Benson.Although I like the company and the people I work with, being on the road for weeks at a time does not appeal to me.I think the situation would be entirely different if I were single or even married with no children.But with two youngsters , traveling represents a real hardship on me and especially on my wife.After each trip it gets increasingly harder for me to treat myself away from my family to go back on the road.

I really have no plans at the moment.I need to take some time to think about what I want to do.I may try to get back into coaching and I’m also considering buying into a local sporting goods store.Whatever I wind up doing, it will have to be something that will permit me to stay anchored in one place.

Thank you for everything you have done for me.I really don’t know how I could received better treatment from a company or a manager.

Sincerely,

Harrod

P.S.In case I need a reference, may I use your name? I would very much appreciate it.

亲爱的本森:

我相信我辞去推销员的职位,你并不会感到奇怪。我将在你认为可行的时候辞职,但不迟于6月12日。

本森,你很清楚我的问题。虽然我喜欢公司,也喜欢于同事们相处,但每次出差在外,一去就是好几个星期,确实让人厌烦。我想如果我尚为结婚或虽结婚而没有孩子的话,情况就完全不同。但现在我有两个孩子 。因此,出差对我,特别是对我的妻子而言的确是件难事。每次出差回来后,我感到要告别我得家人踏上出差的路越来越困惑。

我暂时尚无面向未来的计划。我需要认真考虑一下将来到底作什么。我可能干当教练这一老行当,也可能想买进一家体育用品商店。无论我最终干什么,它必须让我在一个地方稳定地生活,而不必四处奔波。

谢谢您所为我做的一切。

您忠实的

Harrod

推荐第8篇:中英文辞职报告

nameofemployeedepartmentdatejoined

身份证号:职位:合同到期:

i/dno.positiondateofend

辞职原因:(请员工本人填写)最后工作日期:

resignreasonlastworkingday

备注:《员工手册》规定,员工在合同期内离职需提前1个月书面通知或以一个月工资代替通知期,按劳动合同规定办理离职手续

note:

员工签字:日期:

部门经理批准:日期:

推荐第9篇:欢迎词(中英文对照)

欢迎辞

金秋十月,丹桂飘香。蓉城日丽风和,柳林秋高气爽,欣逢2012全球化进程国际学术大会召开之际,我谨代表西南财经大学向远道而来的各位嘉宾致以最热烈的欢迎!

本次全球化进程国际学术大会,以著名经济学家尼古拉·康德拉季耶夫诞生120周年、及其著作“The World Economy and its Conjunctures during and after the War”发表90周年为契机,由西南财经大学与莫斯科罗诺萦夫国立大学共同主办,中国世界经济学会和中国留美经济学会协办,同时,我们十分荣幸地邀请到了来自美国、俄罗斯、英国、德国、乌克兰、澳大利亚、新加坡、南非、瑞士等十多个国家的多名经济学者共聚西南财经大学,参加此次全球化进程国际学术大会。通过为国际范围内的学术对话与讨论搭建平台,全球化进程国际学术大会将成为一次影响范围广、学术水平高、社会意义大的经济学盛会。

全球化是本次会议的讨论主题,也是当今世界格局发展的必然趋势。经济全球化是全球化进程的主要方面,包括了金融全球化、生产全球化、贸易全球化、技术全球化等不同领域的经济现象。借助于经济全球化,世界经济活动超越国界,以对外贸易、资本流动、技术转移、提供服务的方式形成相互依存、相互联系的覆盖全球范围的有机经济整体。经济全球化发展的同时,也将伴随着政治、文化等诸多方面的全球化发展。因此,全球化的时代,是竞争与合作并存、机遇与挑战相倚的时代。对于正处在改革发展关键时期的中国,和其它世界各国,思考如何适应全球化大背景下的多元化发展趋势、如何应对全球化发展衍生出的经济与社会危机、如何在良性竞争的同时实现互利共赢等问题,有着巨大的现实意义。

本次全球化进程国际学术大会将从理论与实际的不同视角,探讨全球化——特别是经济全球化进程中的重点与热点问题,展示当前经济学界在相关领域的最新研究成果。通过对于热点学术问题的相互交流,以及对于当前经济现象的共同思考,必将推动全球化问题研究的进步,为中国改革开放、世界经济的复苏和进一步发展提供丰富的建议。

衷心祝愿各位领导、同僚,各位专家、学者,各位新老朋友们蓉城之行愉快!

西南财经大学 党委书记:赵德武

西南财经大学 校 长:张宗益

二零一二年十月十三日

Welcome Addre Dear Delegates,

On behalf of Southwestern University of Finance and Economics, it is our pleasure to welcome economists from all over the world to “2012 conference on Trends and Cycles in Global Dynamics and Perspectives of World Development” jointly organized by School of Economics of Southwestern University of Finance and Economics (China), Faculty of Global Studies of Lomonosov Moscow State University (Ruia), Institute of Economics Ruian Academy of Sciences (Ruia), The Chinese Economist Society (CES) and China Society of World Economics (CSWE).This year’s conference marks the 120th anniversary of economist Nikolai Kondratieff\'s birth, as well as the 90th anniversary of the publication of his Mirovoye khozyaistvo i ego conyunktury vo vremya i posle voiny [The World Economy and its Conjunctures during and after the War] (Vologda, 1922), where he first spelled out the idea of long cycles, which is known as Kondratieff cycles or Kondratieff waves (or K-waves for short) later.

The global trend is one of the major challenges nowadays, which brings about both advantages and disadvantages to economies all over the world.We will seek to addre iues of globalization with both national and supranational, group and world interests, and identify how countries prepare well for the global trends in an open international economy.Since the world financial crisis has revealed weaknees in some aspects of globalization, the discuion of the current proce and of the multiple economic dimensions is very important to the recovery of the world economy.This conference will provide an opportunity for profeional researchers to present and share the latest perspectives about global dynamics and world development.We have received paper submiions from 18 countries and areas, 85 of which will be presented and discued in 24 seions in this year’s conference.The organizers are grateful to the authors for their enthusiasm and to all the reviewers for their work and time given to evaluate the volunteered submiions in detail.The 2012 conference on Trends and Cycles in Global Dynamics and Perspectives of World Development will offer you up to date studies and researches on globalization and world economy in your field.We specially thank all members of the committee for their contributions to the organization of this conference.

Kind Regards

Dewu Zhao, Zongyi Zhang Southwestern University of Finance and Economics

推荐第10篇:Ghost 中英文对照

Ghost 中英文对照

local 本地机

LPT 网络端口

1.Disk硬盘功能选项

2.Partition 分区功能选项

3.Check 检查功能选项

1.Disk硬盘功能选项:

1>to disk (硬盘复制)

2>to image (硬盘备份)

3>disk from inage (备份还原)

1>to disk (硬盘复制):

(1)选择源盘

(2)选择目标盘

2>to image (硬盘备份)

(1)选择源盘的位置.

(2)选择备份档案储存的位置

3>disk from inage (备份还原)

(1)选择还原档案

(2)选择要还原的硬盘

2.Partition 分区功能选项

1>to Partition (分区复制)

2>to image (分区备份)

3>to from image (还原分区)

1>to Partition (分区复制)

(1)选择来源分区

(2)选择目的分区

2>to image (分区备份)

选择要备份硬盘

选择备份硬盘分区

选择备份档案存放路径与文件名

三种选择: NO 备份时,不压缩.Fast少量压缩.Hight:高比例压缩.3>to from image (还原分区)

(1)选择要还原的备份档案

(2)选择要还原的硬盘

(3)选择要还原的硬盘分区

3.Check 检查功能选项

progre Indicator(步进 指示)

statistics (统计)

percent complete(百分比 完成)

speed cmb/min(速度)

MB copied (复制了)

MB remaining (剩余了)

time elapsed(时间 逝去)

time remaining (时间 剩余)

第11篇:GPS中英文对照

Acquisition Time: 初始定位时间 Active Leg: 激活航线

Adapter: 转接器、拾音器、接合器

Airborne: 空运的、空降的、机载的、通过无线电传播的 Alkaline: 碱性的、碱性 Almanac: 历书、概略星历 Anti-Spoofing: 反电子欺骗

Artwork: 工艺、工艺图、原图 Atomic Clock: 原子钟

Auto-controlling: 自动控制

Avionics: 航空电子工学;电子设备

Azimuth: 方位角、方位(从当前位置到目的地的方向) Beacon: 信标

Bearing: 方向,方位(从当前位置到目的地的方向) Bug: 故障、缺陷、干扰、雷达位置测定器、窃听器 Built-in: 内置的、嵌入的

Cellular: 单元的、格网的、蜂窝的、网眼的 Cinderella: 水晶鞋、灰姑娘

Coarse Acquisition Code(C/A): 粗捕获码 Cold Start: 冷启动

Connector: 接头、插头、转接器 Constellation: 星座

Control Segment: 控制部分

Converter: 转换器、交换器、换能器、变频管、变频器、转换反应堆 Coordinate: 坐标 Co-pilot: 飞机副驾驶

Cost-effective: 成本低,收效大的 Course: 路线、路程、航线

Course Deviation Indicator (CDI): 航线偏航指示

Course Made Good (CMG): 从起点到当前位置的方位 Course Over Ground (COG): 对地航向

Course To Steer(CTS): 到目的地的最佳行驶方向 Crotrack Error (XTE/XTK): 偏航 De-emphasis: 去矫、去加重 Definition: 清晰度

Diagonal: 对角线、斜的、对角线的 Distinguishability: 分辨率

Dropping resistors: 减压电阻器、将压电阻器 Datum: 基准

Desired Track (DTK): 期望航线(从起点到终点的路线) Differential GPS (DGPS): 差分GPS Dilution of Precision (DOP): 精度衰减因子

Elevation: 海拔、标高、高度、仰角、垂直切面、正观图 Enroute: 在航线上、航线飞行 Ephemeris: 星历

Estimated Position Error (EPE): 估计位置误差

Estimated Time Enroute (ETE): 估计在途时间(已当前速度计算) Estimated Time of Arrival (ETA): 估计到达时间 Front-loading data cartridges: 前载数据卡 Geodesy: 大地测量学

Global Positioning System(GPS): 全球定位系统 GLONASS: 俄国全球定位系统

GOTO: 从当前位置到另一航路点的航线 Greenwich Mean Time: 格林威治时间 Grid: 格网坐标 Heading: 航向

Headphone: 戴在头上的收话器、双耳式耳机 Headset amplifier: 头戴式放大器 High-contrast: 高对比度

Intercom: 内部通信联络系统、联络用对讲电话装置 Intersection: 空域交界

Interface Option (I/O): 界面接口选项 Initialization: 初始化 Invert Route: 航线反转 Jack: 插座、插孔 Keypad: 键盘、按键 Kinematic: 动态的

L1 Frequency: GPS信号频率之一(1575.42 MHz) L2 Frequency: GPS信号频率之一(1227.6 MHz) Latitude: 纬度、纬线

Leg (route): 航段,航线的一段

Liquid Crystal Display (LCD): 液晶显示器

Local Area Augmentation System (LAAS): 局域增强系统 Localizer: 定位器、定位发射机、定位信标 Longitude: 经度、经线

Long Range Radio Direction Finding System (LORAN): 罗兰导航系统 Magnetic North: 磁北

Magnetic Variation: 磁偏角 Map Display: 地图显示 Meter: 米

Mount: 安装、支架、装配、管脚、固定件 Multiplexing Receiver: 多路复用接收机 Multipath: 多路径

Nautical Mile: 海里 (1海里=1.852米).Navigation: 导航

Navigation Meage: 导航电文

NAVigation Satellite Timing and Ranging(NAVSTAR) Global Positioning System: GPS系统的全称 National Marine Electronics Aociation (NMEA): (美国)国家航海电子协会 NMEA 0183: GPS接收机和其他航海电子产品的导航数据输出格式 North-Up Display: GPS屏幕显示真北向上 Observatory: 观象台、天文台 Offset: 偏移量

Omnidirectional: 全向的、无定向的

Orientation: 方位、方向、定位、倾向性、向东性 Panel: 仪表盘、面板

Panel-mount: 配电盘装配

Parallel Channel Receiver: 并行通道接收机 P-Code: P码

Photocell: 光电管、光电池、光电元件

Pinpoint: 极精确的、准确定位、准确测定、针尖 Pixel: 象素 Position: 位置 Position Fix: 定位

Position Format: 位置格式

Power-on: 接通电源

Pre-amplifier: 前置放大器 Prime Meridian: 本初子午线

Pseudo-Random Noise Code: 伪随机噪声码 Pseudorange: 伪距

Rack: 齿条、支架、座、导轨 Resolution: 分辨率 Route: 航线

RS-232: 数据通信串口协议

Radio Technical Commiion for Maritime Services (RTCM): 航海无线电技术委员会,差分信号格式

Selective Availability (SA): 选择可用性 Sidetone: 侧音

Source: 信号源、辐射体 Space Segment: 空间部分

Speed Over Ground (SOG): 对地航速

Specifcation: 详述、说明书、规格、规范、特性 Split Comm: 分瓣通信

Squelch:静噪音、静噪电路、静噪抑制电路 Statute Mile: 英里(1英里=1,609米) Straight Line Navigation: 直线导航

Strobe: 闸门、起滤波作用、选通脉冲、读取脉冲 TracBack航向向上显示 Track (TRK): 航向

Transceiver:步话机、收发两用机

Transponder: 雷达应答机、(卫星通讯的)转发器、脉冲转发机 Transducer: 渔探用探头、传感器 Triangulation: 三角测量 True North: 真北

Turn (TRN): 现时航向和目的地之间的夹角 Two-way: 双向的、双路的、双通的

Universal Time Coordinated (UTC): 世界协调时间

Universal Transverse Mercator (UTM): 通用横轴墨卡托投影 U.S.C.G.: 美国海岸警卫队

User Interface: 用户自定义界面 User Segment: 用户部分

Velocity Made Good (VMG): 沿计划航线上的航速 Viewing angles: 视角 Waypoint: 航路点

Wide Area Augmentation System (WAAS): 广域差分系统

World Geodetic System - 1984(WGS-84): 1984年世界大地坐标系 Windshield: 防风玻璃、防风罩 Y-Code: 加密的P码

Yoke: 架、座、轭、磁轭、磁头组、偏转线圈

第12篇:器件中英文对照

器件中英文对照

一、元器件类

RESISTOR电阻

CAPACITOR电容

DIODE二极管

LED发光二极管 TRAFFIC LIGHTS交通灯

LAMP白炽灯

LAMP—FIL电灯泡

DIVIDERN分频器件 PULLDOWN下拉电阻

HDG12864_x128x64 LCD液晶屏

二、仪表类

VSOURCE电压表

DCAMMETER电流表

METER毫安表

三、芯片类

89C52单片机

74LS SERIESTTL74 系列 Operational AmplifiersOP系列运放

四、电源类

BATTERY电池组

CELL干电池

AVCVS电压控制的电压源

ACCVS电流控制的电压源

ACCCS电流控制的电流源

AVCCS电压控制的电流源

五、信号源类

CRYSTAL晶振

六、辅助类

FUSE保险管

AERIAL发射天线

七、逻辑类

AND_xx输入的与非门

第13篇:中英文对照文章⑥

If如果

If you can keep your head when all about you Are losing theirs and blaming it on you;

If you can trust yourself when all men doubt you, But make allowance for their doubting too;

If you can wait and not be tired by waiting,

Or, being lied about,don\'t deal in lies,

Or, being hated, don\'t give way to hating,

And yet don\'t look too good, nor talk too wise;

If you can dreamand not make thoughts your aim; If you can meet with triumph and disaster

And treat those two impostors just the same; If you can bear to hear the truth you\'ve spoken Twiseted by knaves to make a trap for fools,

Or watch the things you gave your life to broken, And stoop and build \'em up with wornout tools;

If you can make one heap of all your winnings And risk it on one turn of pitch-and-to,

And lose, and start again at your beginnings And never breathe a word about your lo;

If you can force your heart and nerve and sinew To serve your turn long after they are gone, And so hold on when there is nothin in you

Except the Will which says to them:\"Hold on!\";

If you can talk with crowds and keep your virtue, Or walk with Kings -nor lose the common touch; If neither foes nor loving friends can hurt you; If all men count with you, but none too much; If you can fill the unforgiving minute

With sixty second\' worth of distance run -

Yours is the Earth and everything that\'s in it, Andyou\'ll be a Man my son!

如果所有人都失去理智,咒骂你,

你仍能保持头脑情形;

如果所有人都怀疑你,

你仍能坚信自己,让所有的怀疑动摇;

如果你要等待,不要因此厌烦,

为人所骗,不要因此骗人,为人所恨,不要因此抱恨,不要太乐观,不要自以为是;

如果你是个追梦人——不要被梦主宰;

如果你是个爱思考的人——光想会达不到目标; 如果你遇到骄傲和挫折

把两者当骗子看待;

如果你能忍受,你曾讲过的事实

被恶棍扭曲,用于蒙骗傻子;

看着你用毕生去看护的东西被破坏,然后俯身,用破烂的工具把它修补;

如果在你赢得无数桂冠之后„

突遇颠峰下跌之险,

失败过后,东山再起,

不要抱怨你的失败;

如果你能迫使自己,

在别人走后,长久坚守阵地,在你心中已空荡荡无一物‟

只有意志告诉你“坚持!”;

如果你与人交谈,能保持风度,

伴王行走,能保持距离;

如果仇敌和好友都不害你;

如果所有人都指望你,却无人全心全意; 如果你花六十秒进行短程跑,

填满那不可饶恕的一分钟—— 你就可以拥有一个世界,

这个世界的一切都是你的,

更重要的是,孩子,你是个顶天立地的人。

第14篇:会计科目中英文对照

100101 人民币(¥) 100102 美元(dollar)

100103 港币(Hongkong dollar)

100201 活期存款(currrent deposit)

10020101

10020102 银存-活期-农行

10020103 银存-活期-中行

10020104 银存-活期-兴业

10020105 银存-活期-交通

10020106 银存-活期-深发

10020107 银存-活期-浦发

100202 定期存款(fixed deposit)

10020201 银存-定期-工行

10020202 银存-定期-农行

10020203 银存-定期-中行

10020204 银存-定期-兴业

10020205 银存-定期-交通

10020206 银存-定期-深发

10020207 银存-定期-浦发

1009 其他货币资金 other cash 100901 外埠存款

100902 银行汇票 bank draft

100903 信用卡存款 credit card deposit 100904 银行本票 cashier\'s cheque 100905 信用证保证金

100906 委托存款 consigned deposit

1101 短期投资 (short-term investment)

110101 股票 (stock)

110102 债券 (bond)

110103 基金 (funds)

110104 其他 (others)

1102 短投跌价准备 (short-term investment impairment provision)

110201 股票 (stock)

110202 债券 (bond)

110203 基金 (funds)

110204 其他 (others)

1111 应收票据 (Notes receivable)

11101 银行承兑 (bank acceptance)

11102 商业承兑 (trade acceptance)

1121 应收股利 (dividends receivable)

1122 应收利息 (interest receivable)

1131 应收账款

1 集团内部单位 inside group 2 集团外部 outside group 9 其他 others

1133 其他应收款 other receivables

1 集团内部单位 other receivables-inside 2 集团外部 other receivables-outside 8 员工 other receivables-employee 9 其他 other receivables-others 1141 坏账准备 provision for bad debt 114101 应收帐款 account receivable 114102 其他应收款 other receivables 2131 预付账款 Advanced to suppliers 1 集团内部单位 inside group 2 集团外部 outside group 9 其他 others

1161 应收补贴款 Subsidy receivable 1192 备用金

1201 物资采购 materials purchasing 1205 在途物资 materials in transit 1211 原材料 raw materials

121101 (4)修理备用件 Spare parts for repair and maintenance 121102 (5)燃料 Fuel 1221 包装物 Containers

1231 低值易耗品 low value articles

123101 办公用低耗品 low value articles for office 123102 工具类低耗品

1232 材料成本差异 variance of material cost 1235 产品成本差异 variance of product cost 1241 自制半成品 semi-manufactured goods 1243 库存商品 Goods sold in stock

1251 委托加工物资 goods in outside proceing 1261 委托代销商品 consigned finished goods 1271 受托代销商品 good commiioned

1281 存货跌价准备 Provision for Inventory impairment 01 原材料 raw materials 02 包装物 Containers

03 低值易耗品 low value articles 04 库存商品 Goods sold in stock 05 自制半成品 Semi-finished goods

06 委托加工 Stores in outside proceing 07 委托代销 good commiioned 08 发出商品 Goods sold

09 分期收款发出商品 Goods sold on installment 1291 分期收款发出商品 Goods sold on installment 1292 发出商品 Goods sold

1301 待摊费用 Prepaid expense 01 低值易耗品 low value articles 02 预付保险 prepaid insurance 03 预付租金 prepaid rent

1401 长期股权投资 Long-term equity investments 01 股票投资 stock investment 01 投资成本 cost of investment 02 损益调整 adjustment for income

03 股权投资差额 variance of investment 04 股权投资准备 provision for investment 02 其他股权投资 others

01 投资成本 cost of investment 02 损益调整 adjustment for income

03 股权投资差额 variance of investment 04 股权投资准备 provision for investment

1402 长期债权投资 Long-term debt investments 01 债券投资 bond investment 01 面值 book value

02 溢价 in exce of par 03 折价 discout 04 利息 interest

02 其他债券投资 other bond investent 01 面值 book value

02 溢价 in exce of par 03 折价 discout 04 利息 interest

1421 长期投资减值准备 Provision for long term investment impairment 01 长期股权投资 Long-term equity investments 01 股票投资 stock investment

02 其他股权投资 other equity investments 02 长期债权投资 Long-term debt investments 01 债券投资 bond investment

02 其他债券投资 other bond investent 1431 委托贷款 consigned loan 1501 固定资产 fixed aet 01 房屋及建筑物 Buildings 02 存储设施 storage

03 运输设备 Transportion vehicles

04 机器设备 Machinery and equipment 05 办公设备 office equipment

06 电子设备 Electronics equipment 07 仪器/仪表

1502 累计折旧 accumulated depreciation 01 房屋及建筑物 Buildings

02 存储设备 storage equipment 03 运输设备 Transportion vehicles

04 机器设备 Machinery and equipment 05 办公设备 office equipment

06 电子设备 Electronics equipment 07 仪器/仪表

1505 固定资产减值准备 provision for fixed aet impairment 1601 工程物资 Coostruction supplies 01 专用材料 special materials 02 专用设备 specialequipment

03 为生产准备的工具及器具 facility prepared for production 1603 在建工程 construction work in proce 01 建筑工程 Expenditure on construction work 02 安装工程 Expenditure on installations work 03 在安装设备 Payment to contractor in advance

1605 在建工程减值准备 Provision forconstruction work in proce impairment 01 建筑工程 Expenditure on construction work 02 安装工程 Expenditure on installations work 03 在安装设备 Payment to contractor in advance

1701 固定资产清理 clearance of fixed aet(Fixed aets pending disposal)

1801 无形资产 intangible aet

01 土地使用权 Land occupancy right 02 sap系统 sap system

03 计算机软件 computer software

1805 无形资产减值准备 allowance for intangibel aets 01 土地使用权 usefruct for land 02 sap系统 sap system

03 计算机软件 computer software 99 其他 oterhs

1815 未确认融资费用 Uncertained finance expense 1901 长期待摊费用 Long-term prepaid aets 1911 待处理财产损溢

01 待处理流动资产损溢

02 待处理固定资产损溢

2101 短期借款 short term load 01 抵押借款 loan in maotagae 02 担保借款 loan in aurance 03 信用借款 loan in credt

2105 应付短期债券 short term bond 01 面值 book value 02 利息 intrest

1218 内部应付款 internal accouts receivable 2111 应付票据 n0te payable

211101 银行承兑 bank acceptance 211102 商业承兑 trade acceptance 2120 专项应付帐款 special account payable

2121 应付账款 account payable 1 集团内部单位 inside 2 集团外部 outside

2131 预收账款 Accounts advanced from customers 1 集团内部单位 inside 2 集团外部 outside 2141 代销商品款

2151 应付工资 Accrued payroll 01 基本工资 basic salary 02 奖金 bonuse 03 补贴 allowance

04 加班费 call-back pay 99 其他 others

2153 应付福利费 Welfare benefits payable 01 提取部分

02 福利人员及医药费

03 职工困难

99 其他

2155 应付利息 interest apybale 2161 应付股利 Dividends payable 2171 应交税金 Taxes payable

217101 应交增值税 value added tax payable 21710101 进项税额 VAT on purchase 2171010101 税率17%

2171010102 税率13%

2171010103 税率7%

21710102

21710103 已交税金 VAT paid

21710104 减免税款 VATreduced and exempted

21710105 出口抵减内销产品应纳税额 VAT payable on domestic sales offset against VAT on purchase for export sales

21710106 转出未交增值税 Transfer out overpaid VAT 21710107 转出多交增值税 Transfer out unpaid VAT 21710108 出口退税 VAT refund for exported goods 21710109 进项税额转出 Transfer out unpaid VAT 21710110 销项税额 VAT on sales 01 非保税

02 保税

217102 未交增值税 unpayed value added tax 217103 应交营业税 sale tax payable 217104 应交所得税 income tax payable 217105 应交房产税 Urbanrealestatetax payable 217106 应交土地使用税

217107 应交城建税

217108 应交车船使用税 Vehiclandveelusagelicencepaltetax payable 217109 应交个人所得税 personale income tax payable 217110 应交印花税 Stamp tax payable

217111 进口关税 Import customs duty payable 2176 其他应交款

01 教育经费 education expense 02 提围费

2181 其他应付款 other payables

218101 工会经费 trad union expense 218102 代扣代缴

01 代扣代缴公积金

02 代扣代缴社保费

03 代扣代缴个人所得税

2191 预提费用 Accrued expenses 01 修理费 repairment expense 2201 待转资产价值

2205 递延收益 deferred income

2211 预计负债 Provisions for foreseeable liabilities 2301 长期借款 long term loan

230101 抵押借款 loan in maotagae 23010101 本金 book value 23010102 利息 interest

230102 信用借款 loan in credt 23010201 本金 book value 23010202 利息 interest

230103 担保借款 loan in aurance 23010301 本金 book value 23010302 利息 interest 230104 其他 others

2311 应付债券 bond payable

2321 长期应付款 Payables due after one year 2331 专项应付款 Govermment grants payable 2341 递延税款 Deferred tax 2351 其他负债 oterh debt

3101 股本(实收资本) Registered capital 01 中方投资 Chinese investment 01 小虎岛公司 xiaohudao company 02 外方投资 Foreign investment 01 泰山集团 TITAN Group

3103 已归还投资 xiaohudao company 01 中方投资 Chinese investment 01 XX公司 Investments returned 02 外方投资 Foreign investment 01 XX集团 XX Group

3111 资本公积 Capital surplus

01 资本(或股本)溢价 capital in exce of par

02 接受捐赠非现金资产准备 donated non-cash aent 03 接受现金捐赠 donated cash

04 股权投资准备 provision for quity investment 05 拨款转入 transfer in 99 其他资本公积 others

3121 盈余公积 Surplus reserve

01 法定盈余公积 Statutory surplus reserve 02 任意盈余公积 Discretionary surplus reserve

03 员工奖励及福利基金 Staff and workers\'bonus and salfare 04 储备基金 Reserve fund

05 企业发展基金 Enterprise expansion fund

3131 本年利润 current year profit(annual profit)

3141 利润分配 distributed profit 01 未分配利润 Undistributed profit

02 计提法定盈余公积 Statutory surplus reserve 03 计提任意盈余公积 Discretionary surplus reserve

04 计提员工奖励及福利基金 Staff and workers\'bonus and salfare 05 计提储备基金 Reserve fund

06 计提企业发展基金 Enterprise expansion fund

07 利润归还投资 Profits capitalised on return of investment 99 应付利润 profit payable

第15篇:中英文对照呼吸机

呼吸机常用专业术语英汉对照关于呼吸机应用中的常见E文如SIMV、CMV、IPPV、PEEP、CPAP等等大家都知道,呵呵,下面的您都知道吗??让我们来学习一下吧。accumulator 贮气箱(装置)adapter 接合器,接口adjusting tap 调节柄air inlet filter 空气输入滤过器airway preure 气道压alarm indicator 报警显示alveolar preure 肺泡内压amplifier . 增幅唇apnea 呼吸暂停apnea indicator 呼吸暂停显示装置aembly 装置、组合back-up ventilation 备用通气bacterial filter 细菌滤过器bag 囊ballon valve 球囊式活瓣bellows 风箱bleed regulator 排气调节器blower 鼓风机calibration 校准、定标chamber 腔check valve 单向阀compensator 代偿装置compreor 压缩器、压缩装置continuous flow 持续气流control knob 调节炳cooling fan 冷却扇corrugated hose 螺纹管,呼吸管道croover soleniod 交通电磁阀delay dial 廷迟设定demand flow 按需气流demand valve 按需供气阀diaphragm 隔膜digital amplifer 数字型增幅器drive system 驱动系统electrical switch 电子开关electrodynamic valve 电动阀exhaled gas 呼出气exhalation time 呼出时间exhalation valve 呼出阀exhaust valve 气体排出活瓣(阀)expired minute volume呼气分钟通气量feed back servocontrol反馈伺服控制filling solenoid 充气电磁阀(气流开关:filter 滤过器flap valve平行阀flow control valve 流量控制(调节)阀flowrate 流速flow transducer 流量传感器flow trigger 流量触发(器)flush knob 冲洗按键gas outlet 气体出口gas samping pump 气体采样泵gas supply 气体供应generated preure 驱动压generator 发生器,产生装置heat exchanger 热交换器heat(heated)humidifier加热(温)湿化器humidifier 加湿气infant ventilator 婴儿呼吸机mjector 喷射器,射流装置inlet 输入(口)lnspiratory effort 自主吸气努力(指示)respiratory time 吸入时间jet 喷射,喷射式joint 连接器(装置)leak test 漏气检查low inspiratory preure sensor吸气低压传感器low preure alert 低压报警限magnetic valve 电磁阀main compreor 主压缩装置(泵)main power 总电源manifold 多歧管manometer 压力计(表)master solenoid 主电磁阀manual 手动membrane 膜,隔膜microproceor 微处理器microswitch 微开关minute volume 分钟通气量mixer 混合器mode 模式moisture trap 湿气(水分)清除装置nebulizer 雾化器(装置)needle valve 针型阀one-way valve 单向阀orifice

13、孔、开口overflow valve 满溢阀(活瓣)over-preure relif valve过压释放阀oxygen percent control 氧浓度调节(控制)oxygen sensor 氧传感器parameter 参数pat~nt wye Y型接头peak hold switch 峰压保持键peak flow dial 峰流设定plateau平台plunger 插塞pneumotachometer 气流速度计piston 活塞pop off valve 过压释放阀preset volume(preure)预置的容量(压力)power supply 电源preure gauge 压力计、压力测量装置preure manometer 压力计(表)preure-reducing valve 减压阀preure regulator 压力调节器preure relief valve 压力释放阀preure support 压力支持preure transducer 压力传感器proportional solenoid 比例电磁阀valveproximal airway line 气道压测量联接管ratio 率、比值regulator 调节器(装置)reservoir hag 贮气囊resetkey 复原键、恢复键respiratory hag 呼吸囊respiratory rate 呼吸频率restrictor 气流限制装置reverse flow 逆流sensitivity 敏感度sensor 传感器、测量器sigh preure 息时压力silicone rubber tube 硅橡胶管slipjoint 滑动关节solenoid 电磁阀、电控气流阀(开关)source gas 气源spirometer 肺活量计spontaneous bag 自主呼吸囊spring 弹簧stepping(stepper,step)motor 步进电机stopcock 气流开关suction 吸引support arm 支持臂temperature sensor 度传感器test lung 模拟肺thermister 半导体温度计thermometer 度计tidal volume 潮气量time preset key 时间预调键tranducer 传感器trigger level 触发水平tubingcompliance 管道顺应性variable orifice 可变口valve 阀,活瓣vent 出口ventilator 呼吸机、通气机ventilator settings 呼吸机设置Venturi 文丘里装置water trap 除水装置waveform 波形wick 加湿器的芯子

第16篇:中英文对照辞职信

英语辞职信(中英对照版) dear hr leadership: but i need to resign for personal reasons.in regularization with my salary after the nature of work and measure my ability to work, i feel the salary is not with my expectations.so, i decided to resign. i hope my applications can be approved before june 20, i wish you good health . applicant: jack date: june 22, 2010 尊敬的人力资源部领导:

我很遗憾自己在这个时候向公司正式提出辞职。

我来公司刚好三个月了,也很荣幸自己能够成为医院的一员。在医院工作的三个月中,我学到了很多东西,公司的经营状况也处于良好的态势。非常感激公司给予了我在这样的良好环境中,工作和学习的机会。

但是我因为个人原因需要辞职。在对转正后的薪资与我的工作性质和自己工作能力的衡量后,我觉得与自己的预期不相符合,出于对医院制度的尊重及个人发展的考虑,我决定了辞职。

我希望在2010年7月20日之前完成工作交接,请领导安排工作交接人选。在未离开岗位之前,我一定会站好最后一班岗,我所在岗位的工作请领导尽管分配,我一定会尽自己的职,做好应该做的事。

望领导批准我的申请,并请协助办理相关离职手续。

祝您身体健康,事业顺心。并祝医院以后事业蓬勃发展。

申请人: 杰克

日期: 2010年6月22日篇2:中英文辞职信范本(全) 辞职函

xxxxx有限公司总经理室:

各位领导,我带着复杂的心情写这封次致信。由于您对我的能力的信任,使我得以

加入公司,并且在短短的两年间获得了许多的机遇和挑战。经过这两年在公司从事的 xx开发和xx管理工作,使我在xx开发,xx管理等领域学到了很多知识、积累了一定 的经验。对此我深怀感激!

由于薪金的原因,我不得不向公司提出申请,并希望能与今年x月xx日正式离职。

对于由此为公司造成的不便,我深感抱歉。但同时也希望公司能体恤我的个人实际,

对我的申请予以考虑并批准为盼。

此致

敬礼

申请人:

年月日

再来:

-------------

亲爱的××领导:

我可能会在×月份某个你觉得方便的时候离开公司。

自从××××年入职以来,我一直都很享受这份工作。转眼快×年过去了,我要重

新确定我未来的方向。诚然,论工作环境、团队、压力,甚至个人喜好,我都很满意。

但,因为某些个人的理由

,我最终选择了开始新的工作。希望你能早日业胶鲜实娜耸纸犹嫖业墓ぷ鳌? 当然,若你容许的话,我愿意,并且渴望在工余时间,为我们这个团队继续出力,

最后,我也不知道可以说什么,只能忠心对你说对不起与谢谢你,并祝愿您和大家能开

创出更美好的未来。

×× 敬上 it is with both regret and anticipation that i submit this letter of resignation, to resign from the position of 职位 effective february xx, 2004.i have decided to take this time to evaluate my current goals and investigate new opportunities. it has been my genuine pleasure to work for edward keller and 公司名group during these last xx years. thank you for allowing me to 公司名. yours sincerely 辞 职 报 告

从2002年初至今,进入公司工作两年的时间里,得到了公司各位同事的多方帮助,

我非常感谢公司各位同事。

在过去的两年里,我在公司里工作的很开心,感觉公司的气氛就和一个大家庭一样, 大家相处的融洽和睦,同时在公司里也学会了如何与同事相处,如何与客户建立良好关

系等方面的东西。并在公司的过去两年里,利用公司给予良好学习时间,学习了一些新

的东西来充实了自己,并增加自己的一些知识和实践经验。我对于公司两年多的照顾表

示真心的感谢!!

在经过2003年下半年的时间里,公司给予了很好的机会,让自己学习做市场方面 的运做,但由于自己缺乏市场等方面的经验,自己没有能很好的为公司做好新的市场开

发,自己身感有愧公司的两年的培养。

由于我个人感觉,我在过去的一段时间里的表现不能让自己感觉满意,感觉有些愧

对公司这两年的照顾,自己也感觉自己在过去两年没有给公司做过点贡献,也由于自己

感觉自己的能力还差的很多,在公司的各方面需求上自己能力不够。所以,经过自己慎

重考虑,为了自己和公司考虑,自己现向公司提出辞职,望公司给予批准。

签名:

年月日

辞职书范文真诚版、简易版

辞职书范文一(真诚版) 尊敬的z主任:

您好!

工作近四年来,发现自己在工作、生活中,所学知识还有很多欠缺,已经不能适应

社会发展的需要,因此渴望回到校园,继续深造。经过慎重考虑之后,特此提出申请:

我自愿申请辞去在xxx的一切职务,敬请批准。

在xxx近四年的时间里,我有幸得到了单位历届领导及同事们的倾心指导及热情 帮助。工作上,我学到了许多宝贵的科研经验和实践技能,对科研工作有了大致的了解。

生活上,得到各级领导与同事们的关照与帮助;思想上,得到领导与同事们的指导与帮

助,有了更成熟与深刻的人生观。这近四年多的工作经验将是我今后学习工作中的第一

笔宝贵的财富。

在这里,特别感谢yyy(xxx的上级单位)a主任、b主任、c主任在过去的工作、

生活中给予的大力扶持与帮助。尤其感谢xxxz主任在xxx近二年来的关照、指导以 及对我的信任和在人生道路上对我的指引。感谢所有给予过我帮助的同事们。

望领导批准我的申请,并请协助办理相关离职手续,在正式离开之前我将认真继续

做好目前的每一项工作。

祝您身体健康,事业顺心。并祝yyy、xxx事业蓬勃发展。 *** **年**月**日

辞职书(公司职员)范文二

尊敬的主管、副理:

您好!

在公司工作一年中,学到了很多知识,公司的营业状态也是一直表现良好态势。非常感激公司给予了我这样的机会在良好的环境工作和学习。虽然在公司里基础的业务知识及专业知识已经基本掌握,但俗话说“学无止境”,有很多方面还是需不断学习。提出辞职我想了很久,公司的环境对于业务员很照顾很保护(至少对于业务风险来说),鉴于我的个性,要在公司自我提升及成长为独挡一面的能手,处于保护的环境下可能很难。我自己也意识到了自己个性倾于内向,你们也有经常提醒我这一点,其实,这不管是对于公司培育人才或是我自身完善都是突破的难点。

虽然我的观念是:人需要不断的发展、进步、完善。我也一直在努力改变,变得适应环境,以便更好的发挥自己的作用。但是我觉得自己一直没什么突破,考虑了很久,确定了需要变换环境来磨砺。

公司业务部近期人员变动较大,因此交接工作可能需要一个时期。我希望在10/24左右完成工作交接。这个时间也许比较紧,如果实施上有太多困难,我同意适当延迟一周。但是我还是希望副理理解,现临近年底,如果能给予我支配更多的时间来找工作我将感激不尽!

我希望在我提交这份辞程的时候,在未离开岗位之前,是我的工作请主管尽管分配,我一定会尽自己的职,做好应该做的事。另外,希望主管不要挽留我,其实,离开是很舍不得,原因自不用说明。但是既已决定,挽留会让我最终离开的时候更为难。谢谢∽詈螅m镜囊导ㄒ蝗缂韧宦缝≈鞴芗案魑煌使ぷ魉忱?nbsp; 辞职申请书范文三

公司人事部:

我因为要去美国留学,故需辞去现在的工作,请上级领导批准。

公司的企业文化感化了我,我对公司是深有感情的。我留学归来之后,仍愿意回公司就职。

感谢公司领导和同事在工作中对我的关心和支持,并祝公司兴隆。

辞职信模板(推荐)

尊敬的领导:

我很遗憾自己在这个时候向公司正式提出辞职。

来到**公司也快两年了,正是在这里我开始踏上了社会,完成了自己从一个学生到社会人的转变。有过欢笑,有过收获,也有过泪水和痛苦。公司平等的人际关系和开明的工作作风,一度让我有

着找到了依靠的感觉,在这里我能开心的工作,开心的学习。然而工作上的毫无成熟感总让自己彷徨。记得胡总曾说过,工作上如果两年没起色就该往自己身上找原因了。或许这真是对的,由此

我开始了思索,认真的思考。尽管我一思考,上帝便会发笑,但这笑带着一丝苦涩,思考的结果连自己都感到惊讶――或许自己并不适合软件开发这项工作。否定自己让自己很痛苦,然而人总是 要面对现实的,自己的兴趣是什么,自己喜欢什么,自己适合做什么,这一连串的问号一直让我沮丧,也让我萌发了辞职的念头,并且让我确定了这个念头。或许只有重新再跑到社会上去遭遇挫

折,在不断打拼中去寻找属于自己的定位,才是我人生的下一步选择。从小到大一直过得很顺,这曾让我骄傲,如今却让自己深深得痛苦,不能自拔,也许人真的要学会慢慢长大。

我也很清楚这时候向公司辞职于公司于自己都是一个考验,公司正值用人之际,sun ltd.erp 2004项目启动,所有的前续工作在公司上下极力重视下一步步推进。也正是考虑到公司今后在这个项

目安排的合理性,本着对公司负责的态度,为了不让公司因我而造成的决策失误,我郑重向公司提出辞职。我想在项目还未正式启动开始之前,公司在项目安排上能做得更加合理和妥当。长痛不

如短痛,或许这对公司对我都是一种解脱吧。

能为公司效力的日子不多了,我一定会把好自己最后一班岗,做好项目开始前的属于自己的所有工作,尽力让项目做到平衡过渡。

离开这个公司,离开这些曾经同甘共苦的同事,很舍不得,舍不得领导们的譐譐教诲,舍不得同事之间的那片真诚和友善。

也愿公司在今后的工作中发挥优势,扬长避短,祝愿公司兴旺发达!

辞职人:*** 年月日 2008最新英文辞职信模板下载 sample 1 addre city, state zip date addreee addre city, state zip dear as i go to the new position, i’ll do so with the utmost respect for the management examples and philosophies learned here and with gratitude for the personal attention to my career growth. thank you for the rewarding experience i痸e enjoyed during my seven-year aociation with the organization. 最新辞职申请书辞职报告范文

尊敬的徐总及公司领导:

我很遗憾自己在这个时候向公司正式提出辞职。

来到公司大约半年了,公司里的人对我都很好。我衷心感谢徐总以及各位同事对我的照顾与错爱,在这半年里,我学到了很多以前从未接触过的知识,开阔了视野,锻炼了能力。而今,我决定离开,也许这样会好一些。

因为诸多原因,我决定参加2007.1的研究生考试,以为工作两年再去读研是一个好的决定。如果我现在不辞职,我就是在公司里尸位素餐两年,因为在两年时间里,我不可能为公司做多少贡献。我也许能大致经历、学习这个工程建设的某些方面,可这只是对我有好处,只会使我欠公司更多的情。考虑到公司在人员安排上的合理性,本着对公司负责的态度,为了不让公司因我而造成决策的失误,我郑重向公司提出辞职。 因为有想考中山大学的研究生,前几天一位老乡告诉我中大招一名热工的本科生做实验助理。这对我而言是一个很好的机会,学校的氛围肯定更加适合准备考研,我在1.4已经把我的相关资料寄过去了。我希望尽快解除与公司的劳动关系,可以安心地轻轻离开。 也许我该提前一个月给您递呈辞职报告,好在我手头的工作不多,一个星期足以交接干净。我原本打算1.16开始我的二十余天的探亲假,现在我希望所有该处理的事情都在 1.13(周五)前处理妥当。马上就要离开公司了,在这最后的一段时间里,我会做好所有的交接工作,正常上班,静心等待您的答复、处理。

离开这个公司,我满含着愧疚、遗憾。我愧对公司上下对我的期望,愧对各位对我的关心和爱护。遗憾我不能经历工业园的发展与以后的辉煌,不能分享你们的甘苦,不能聆听各位的教诲,也遗憾我什么都没能留下来。我将就这样悄悄地离开,结束我的这第一份工作。

最后,衷心祝愿公司健康成长,事业蒸蒸日上!祝愿各位领导与同事:健康快乐,平安幸福!篇3:辞职信_中英文

辞职申请书

尊敬的领导:

由于我的一些个人原因,经过一段时间的慎重考虑后,我决定向公司提出辞职。

在短短一年的时间里,公司给予了我多次机会,使我在这个工作岗位上积累了一定的技术技能和工程经验。我在公司里工作的很开心,感觉公司的气氛就和一个大家庭一样,大家相处的融洽和睦,同时在公司里也学会了许多工作以外的处世为人等做人的道理。所有的这些我很珍惜也很感谢公司,因为这些都为我在将来的工作和生活中带来帮助和方便。 另外,在和各位同事的朝夕相处的时间里,也使我对过去的、现在的同事建立了由浅到深的友谊,我从内心希望这份友谊,这份感情能继续并永久保持下去。

今后,无论我将怎样生活,我都会永远感激公司对我的培养,各级领导和同事给我的支持和帮助。在我困难的时候,犯错的时候给我的帮助和宽容。公司是一棵参天大树,而我,只不过是树上的一片叶子。每当风起时,都有些树叶会掉落,但是,大树总是那么挺拔和伟岸。

离开这个公司,离开这些曾经同甘共苦的同事,很舍不得,舍不得领导们的谆谆教诲,舍不得同事之间的那片真诚和友善。

对于由此为公司造成的不便,我深感抱歉。但同时也希望公司能体恤我的个人实际,批准我的申请。

第17篇:防疫针中英文对照

儿童常用疫苗可以预防的疾病给中英文对照表

疫苗名称 英文简称 可预防的传染病

卡介苗 Bacillus Calmette Guerin =B.C.G 结核病

脊髓灰质炎活疫苗 Poliomyelitis =POLIO 脊髓灰质炎(小儿麻痹症)

百白破混合制剂 DTP 百日咳 白喉 破伤风

麻疹疫苗 Measles (rubeola) 麻疹

乙脑疫苗 Japanese encephalitis 流行性乙型脑炎

乙肝疫苗 Hepatitis B 乙型病毒性肝炎

风疹疫苗 Rubeola (German measles) 风疹

流脑疫苗 Meningitis 流行性脑脊髓膜炎

腮腺炎疫苗 mumps 流行性腮腺炎

麻腮风疫苗 MMR 麻疹 风疹 流行性腮腺炎

流感疫苗 haemophilus influenza B 流行性感冒

甲肝疫苗 Hepatitis A 甲型病毒性肝炎

水痘疫苗 Varicella 水痘 带状疱疹

Hib(乙型流感)疫苗 Hib Hib引起的小儿脑膜炎 肺炎等

伤寒疫苗 Typhoid 伤寒

肺炎疫苗 Pneumococcal 肺炎

白喉破伤风疫苗 Td 白喉破伤风

DTP 包括 百日咳Pertuis(whooping cough) 白喉diphtheria 破伤风tetanus

防疫针的中英文对照

这是北京出入境检验检疫局给的“国际预防接种证书”上的防疫针的中英文对照。希望可以

帮到有需要的妈妈们。

卡介苗:BCG

脊髓灰质炎:Poliomyelitis

百白破:DTP

麻疹:Measles

流脑:Meningitis

乙脑:Japanese encephalitis

乙肝:Hepatitis B

风疹:Rubella

腮腺炎:Mumps

甲肝:Hepatitis A

伤寒:Typhoid

白喉破伤风:Td 水痘:Varicella 肺炎:Pneumococeal 流行性感冒:Influenza

乙脑流感:Hib 麻风腮:MMR

第18篇:zemax 中英文对照

近轴光线(Paraxial Rays); 镜头数据(Lens Data); 插入或删除面数据 (Inserting and deleting surfaces); 输入面注释(Entering surface comments); 输入半径数据(Entering radii data); 输入厚度(Entering thickne data); 输入玻璃数据(Entering gla data); 输入半口径数据(Entering semi-diameter); 输入二次曲面数据(Entering conic data); 输入参数数据 (Entering parameter data); 确定光栏面(Defining the stop surface); 选择面型(Selecting surface types); 各面通光口径的确定(Specifying surface apertures); 用户自定义口径和挡光(User defined apertures and obscurations); 到达表面和从表面射出的光线的隐(Hiding rays to and from surfaces); 设置和撤销求解(Setting and removing solves); 光圈类型 (Aperture Type); 入瞳直径 (Entrance Pupil Diameter); 像空间F/# (Image Space F/#); 物空间数值孔径(Object Space Numerical Aperture)物空间边缘 光线的数值孔径(nsinθm);

藏通过光栏尺寸浮动(Float by Stop Size);近轴工作F/#(Paraxial Working F/#); 物方锥形角 (Object Cone Angle); 光圈值 (Aperture Value); 镜头单位 (Lens Units); 玻璃库 (Gla Catalogs); 光线定位 (Ray Aiming); 使用光线定位贮藏器 (Use Ray Aiming Cache); 加强型光线定位(慢)(Robust Ray Aiming (slow); 光瞳漂移:X,Y,Z (Pupil Shift:X,Y,and Z); “视场光瞳偏移比例因子” (Scale pupil shift factors by field); 变迹法 (Apodization Type); 变迹因子 (Apodization Factor); 光程差参数 (Referece OPD);近轴光线 (Paraxial Rays); 快速非球面追迹 (Fast Asphere Trace); 检查梯度折射率元件的口径 (Check GRIN Apertures); 半口径余量% (Semi Diameter Margin in %); 半口径的快速计算法(Fast Semi-Diameters); 全局坐标参考面 (Global Coordinate Reference Surface); 视场 (Fields); 偏振状态 (Polarization State); 外形图(Layout); 二维外形图(2D Layout); 3D外形图(3D Layout); 立体模型(Solid Model);光线像差(Ray Aberration); 光程(Optical Path); 光瞳像差(Pupil Abberation); 离焦(Through Focus); 全视场(Full Field); 矩阵(Matrix); 球差(W040), 彗差(W131), 像散(W222), 匹兹凡场曲(W220P), 畸变(W311), 轴向色离焦项(W020), 轴向色倾斜(W111), 弧矢场曲(W220S),平均场曲(W220M), 子午场曲(W220T); 优化 (Optimization); 全局优化(Global Search); 锤形优化(Hammer Optimization); 消除所有的变量(Remove All Variable); 评价函数列表(Merit Function Listing); 公差(Tolerancing); 公差列表(Tolerance Listing); 公差汇总表(Tolerance Summary); 镀膜列表(Coating Listing); 变换半口径为环形口径(Convert Semi-Diameter to Circular Apertures); 镜头缩放(Scale Lens); 生成焦距(Make Focal); 快速调焦(Quick Focus) 添加折叠反射镜(Add Fold Mirror); 幻像发生器(Ghost Focus generator); 系统复杂性测试(Performance Test); 表面数据(Surface Data); 系统数据(System Data); 规格数据(Prescription Data);

solve type是zemax中用于设定光学系统结构(Curvature、Thinkne、Cla、Semi-Diameter、Conic、Parameter)的操作参数,设定正确的solve type是优化光学系统结构的前提。

Curvature的solve type设定:

Fixed:(无参数)表示Curvature是固定的值,在优化时不能改变 Variable:(无参数)表示Curvature是可变化值,在优化时可以改变 Marginal ray angle:(角度)通过设定近轴边缘光线角度设定Curvature Chief ray angle:(角度)通过设定近轴主光线角度设定Curvature Pick up:(面数,倍率)通过设定与相应面数Curvature的倍率关系设

定Curvature Marginal ray normal:(无参数)通过设定面与近轴边缘光线垂直设定Curvature Chief ray normal:(无参数)通过设定面与近轴主光线垂直设定Curvature Aplanatic:(无参数)通过设定相对于近轴边缘光线的等光程面设定Curvature Element power:(公式参数)根据公式设定Curvature,具体公式参考zemax手册

Concentric with surface:(面数)通过设定曲率中心在相应面数上设定Curvature Concentric with radius:(面数)通过设定Curvature与相应面数Curvature同心设定Curvature F/#:(近轴F数)通过设定近轴边缘光线满足F/#条件设定Curvature

Thickne的solve type设定:

Fixed:(无参数)表示Thickne是固定的值,在优化时不能改变 Variable:(无参数)表示Thickne是可变化值,在优化时可以改变

Marginal ray height:(高度,瞳区)通过设定过瞳区的近轴边缘光线到下一面上的高度设定Thickne Chief ray height:(高度)通过设定近轴主光线到下一面上的高度设定Thickne Pick up:(面数,倍率,偏移量)通过设定与相应面数Thinkne的倍率关系和偏移量设定Thickne Optical path difference:(光程差,瞳区)通过设定瞳区内的近轴边缘光线与近轴主光线的光程差设定Thickne Position:(面数,距离)通过设定到相应面数的距离设定Thickne Compensator:(面数,距离)通过设定与相应面数的Thickne和设定Thickne Center of curvature:(面数)通过设定下一面位于相应面数曲率中心设定Thickne Gla的solve type设定:

Fixed:(无参数)表示Gla是固定的值,在优化时不能改变 Model:(折射率,色散系数,中部色散)通过设定折射率,色散系数,中部色散设定Gla Pick up:(面数)通过设定与相应面数Gla相同设定Gla Substitute:(目录名)通过让zemax在设定的目录名中寻找适合的Gla Offset:(折射率偏移量,色散系数偏移量)通过设定折射率偏移量和色散系数偏移量设定Cla Semi-Diameter的solve type设定: Automatic:(无参数)表示Semi-Diameter由系统自动确定,在优化时可以改变

Fixed:(无参数)表示Semi-Diameter是固定的值,在优化时不能改变

Pick up:(面数)通过设定与相应面数Semi-Diameter相同设定Semi-Diameter Maximum:(无参数)表示由系统自动确定统一的Semi-Diameter(取最大的Semi-Diameter),在优化时可以改变 Conic的solve type设定: Fixed:(无参数)表示Conic是固定的值,在优化时不能改变 Variable:(无参数)表示Conic是可变化值,在优化时可以改变 Pick up:(面数,倍率)通过设定与相应面数Conic的倍率关系设定Conic Parameter的solve type设定:

Fixed:(无参数)表示Parameter是固定的值,在优化时不能改变 Variable:(无参数)表示Parameter是可变化值,在优化时可以改变

Pick up:(面数,倍率,偏移量)通过设定与相应面数Parameter的倍率关系和偏移量设定Parameter

第19篇:VRay中英文对照

VRay 材质

VRay渲染器提供了一种特殊的材质-VrayMtl-VRay材质。在场景中使用该材质能够获得更加准确的物理照明(光能分布),更快的渲染,发射和折射参数调节更方便。使用VrayMtl,你可以应用不同的纹理贴图,控制其反射和折射,增加凹凸贴图和置换贴图,强制直接全局照明计算,选择用于材质的BRDF。该材质的参数都列入以下部分。 Basic parameters Diffuse – 这是该材质的漫射颜色。你可以在texture maps部分中的折射贴图栏中,使用一种贴图来覆盖它。

Reflect – 漫反射颜色的倍增器。你可以在texture maps部分中的反射贴图栏中,使用一种贴图来覆盖它。

Gloine – 该值表示该材质的光泽度。当该值为0.0时表示特别模糊的反射。当该值为1.0时将关闭材质的光泽(VRay将产生一种特别尖锐的反射)。注意,提高光泽度将增加渲染时间。

Subdivs – 控制发射的光线数量来估计光滑面的反射。当该材质的Gloine (光泽度)值为1.0时,本选项无效。(VRay不会发出任何用于估计光滑度的光线) Fresnel reflection – 当该选项选中时,光线的反射就象真实世界的玻璃反射一样。这意味着当光线和表面法线的夹角接近0o时,反射光线将减少至消失。(当光线与表面几乎平行时,反射将是可见的,当光线垂直于表面时将几乎没有反射。)

Max depth – 贴图的最大光线发射深度。大于该值时贴图将反射回黑色。 Refract – 折射倍增器。你可以在texture maps部分中的折射贴图栏中,使用一种贴图来覆盖它。

Gloine -该值表示该材质的光泽度。当该值为0.0时表示特别模糊的折射。当该值为1.0时将关闭材质的光泽(VRay将产生一种特别尖锐的折射)。注意,提高光泽度将增加渲染时间。

Subdivs -控制发射的光线数量来估计光滑面的折射。当该材质的Gloine (光泽度)值为1.0时,本选项无效。(VRay不会发出任何用于估计光滑度的光线)

IOR – 该值决定材质的折射率。假如你选择了合适的值,你可以制造出类似于水,钻石,玻璃的折射效果。在本手册的术语部分有一个有用的材质折射率表。 Max depth -贴图的最大光线发射深度。大于该值时贴图将反射回黑色。 Translucent – 打开透明功能。注意此时你的灯光必须使用VRay阴影才能使用该功能。材质的表面光泽Gloy也要打开。VRay将使用Fog color来决定通过该材质里面的光线的数量。

Thickne – 该值决定透明层的厚度。当光线进入材质的深度达到该值时,VRay将不会进一步追踪在该材质内部更深处的光线。

Light multiplier – 光线亮度倍增器。它描述该材质在物体内部所反射的光线的数量。 Scatter coeff – 该值控制透明物体内部散射光线的方向。当该值为0.0时表示物体内部的光线将向所有方向散射。当该值为1.0时表示散射光线的方向与原进入该物体的初始光线的方向相同。

Fwd/bck coeff – 该值控制在透明物体内部有多少散射光线沿着原进入该物体内部的光线的方向继续向前传播或向后反射。当该值为1.0时表示所有散射光线将继续向前传播。当该值为0.0时表示所有散射光线将向后传播。当该值为0.5时表示向前和向后传播的散射光线的数量相同。

Fog color(see Gloine in Reflection params section) Subdivs(see Low subdivs in Reflection params section) Translucent – 打开透明功能。注意,你的灯光必须使用VRay阴影该功能才起作用。同时,Gloy也必须打开。VRay将使用Fog color 来决定通过材质内部光线的数量。

Thickne – 该值决定透明体的厚度。当光线深度达到该值时,VRay将不再对物体内的光线进行追踪。

Light multiplier – 灯光作用倍增器。它描述了实际上反射的灯光的数量。

Scatter coeff – 该值控制透明物体内部散射光线的方向。当该值为0.0时表示物体表面的光线将沿所有方向散射。当该值为1.0时,表示光线的散射方向与原光线进入物体的方向相同。

Fwd/bck coeff – 该值决定在原来进入物体的光线中,有多少散射光线会进一步向前或向后传播。当该值为1.0时,表示所有光线都将继续向前传播。当该值为0.0时,表示所有光线都向后传播。当该值为0.5时,表示向前和向后传播的光线数量相同。

Fog color – VRay允许你使用体积雾来填充透明物体。这里是体积雾的颜色。 Fog multiplier –体积雾倍增器,较小的值会产生更透明的雾。

Max depth – 折射光线的最大追踪深度。(see Max depth in Reflection params section) Degrade depth(see Cutoff thresh in Reflection params section) Exit color - (see Exit color in Reflection params section) Ray 阴影

VRay支持面阴影,在使用VRay透明折射贴图时,VRay阴影是必须使用的。同时用VRay阴影产生的模糊阴影的计算速度要比其它类型的阴影速度快。

Transparent shadows – 当物体的阴影是由一个透明物体产生的时,该选项十分有用。当打开该选项时,VRay会忽略MAX的物体阴影参数 (Col or, Dens., Map, etc.)。当你需要使用MAX的物体阴影参数时,关闭该选项。 Area shadow – 打开或关闭面阴影。

Box – VRay计算阴影时,假定光线是由一个立方体发出的。 Sphere – VRay计算阴影时,假定光线是由一个球体发出的。 U size – 当计算面阴影时,光源的U尺寸。(如果光源是球形的话,该尺寸等于该球形的半径)

V size -当计算面阴影时,光源的V尺寸。(如果选择球形光源的话,该选项无效) W size -当计算面阴影时,光源的W尺寸。(如果选择球形光源的话,该选项无效) Subdivs – 该值用于控制VRay在计算某一点的阴影时,采样点的数量。

Low subdivs –当采用低精度计算时,该值用于控制VRay在计算某一点的阴影时,采样点的数量。

Degrade depth – 该值描述VRay在该光线追踪深度时,转换为低精度计算。 Bias – 某一给定点的光线追踪阴影偏移。

第20篇:沙发中英文对照

沙发常用英语

wood frame木架arm chair单人沙发 loveseat双人沙发sharp edge棱角 open scars开口伤healed scars愈合伤

untidy乱/不整齐slant歪斜 T \\ E9d h back cushion 靠背cushion垫子 foam海棉welt cord嵌条

skite panel裙边frame wrok结构/组成 fire brand烙印protrude突出 rise up鼓起

wrong dimensio 尺寸错误

pleat打褶

tael流苏

preing熨平

4 leg not in level4脚不平

factory工厂

back后

liming 去毛(浸灰,石灰处理)

splitting分层

shaving削匀

drying干燥

finishing喷浆(整饰,涂装)

trimming清理(修边)

semi-aniline半苯胺

suede split起绒二层

neck wrinkles颈纹

belly腹部

carf小牛

crocking掉色,磨擦脱色

full-grain全粒面

luster铜绿光泽

pigment颜料

two-tone双色革

shrink缩水,收缩

wax leather蜡变革

light corrected grain轻修皮

sammiering挤水

Velcro魔术贴

Cushion border 座垫四周

Out arm扶手外侧

Outside back后下

Healed scar愈合疤痕

Stitch缝针

We嵌条ticking内套to jion or stick with glue用胶粘贴zipper拉链fringe排须/须边bra nail铜钉余额front前side侧fleshing去肉tanning鞣制dyeing染色staking振荡(拉软)printing压花pure-aniline全苯胺corrected grain修面革veins纹理scars疤痕nu-buck磨沙革hide兽皮,皮革, 压花(饰以图案)hand-rub手擦patina光泽pull-up油变革backbone脊椎top grain头层皮)wet blue蓝湿皮milling 干滚(在转鼓中)cut\\sew裁剪缝纫Cushion座垫In arm扶手内侧Front arm panel 扶手前板Open scar开裂疤痕Seam缝边 双针打结,扭曲balanceemboingDouble needle stitchKink

Denim里布Flammability可燃

Compreion压力Drop in coil连体簧

8-way hand tied 人工绑(宝塔簧)zigzag springS簧

notch刀眼PVC仿皮

Decking material 里布,衬布Logo material 里布,衬布:

Liner material里布,衬布Incandescent白炽灯

Fluorescent荧光灯Suede小山羊皮

Micro fiber麂皮绒Jacpuard提花

Plaid格子花呢Fireproof防火

Daylight日光Tapestry织锦

Damask缎子Latex浮胶

Backing背胶Yarn dye色织

Piece dye披染Chenille雪尼尔

Polyester涤纶Rayon人造纤维织物

Warp经线woof\\weft纬线

fringe排须tael流苏,缨,坠子

skirt裙边webbing松紧带,绷带

elastic webbing 弹性绷带plygrip反包条,反包扣

plump饱满的needle work缝纫

saddle stitch双针crown patch加胖海棉

non-woven fabric 无纺布throw pillow 抱枕,抛枕

bolster长枕kidney pillow腰枕

stripe条纹,斑纹down绒毛(水禽)

duck鸭绒

dtp(down proof ticking)防雨布notch risistance 撕破强度

wearing test 耐磨测试blocking 高温粘着测试

printed emboed grain压花粘面preesing 熨平

wearing capacity 耐磨性wearing property 耐磨性

water repellency拒水性water resistance抗水性

water proof防水性lumpy块状不平的

plaid格子花呢bias斜纹,斜的

fireproof防火left side face 对面左侧

right side face 对面右侧raw edge未锁的边中

Vocabulary about sofa

木架相关:

木架Wood(en) frame硬木、实木Hard wood\\Solid wood夹板, 胶合板Plywood木材Lumber

干燥的Dried树瘤Tree tumor(Burls)

虫孔Wormhole霉斑Visible mold

蛇形簧Serpentine spring/Zigzag spring绷带Elastic

Bandage

海绵相关:

海绵Foam密度Density回性Elasticity软硬度Flex硬的Hard软的Soft

海绵包Sponge bag弹簧包Spring Package防火的Fireproof

防火绵Fireproof(ing) foam

英标防火绵UK Standard Fireproofing Foam

美标防火绵CA Standard Fireproofing Foam

皮料相关:

真皮Genuine leather人造皮(合成革)Synthetic leather

进口皮Imported leather再生皮Bounded leather

头层皮Top (leather)二层皮Split (leather)

全粒面皮Full grain leather水牛皮Buffalo leather

(黄)牛皮Cattle hidePU、PVC两种做配皮的人造皮色差Color difference色深Color depth

颜色太深(浅)The color is dark(light).

尺寸相关:(1英寸=2.54里面1 Inch=2.54CM)

尺寸Dimension长length宽width高height

坐垫高Seat height扶手高Arm height沙发脚高度Sofa leg height

沙发相关描述:

沙发床Sofa bed功能沙发Functional sofa

转角沙发Corner sofa组合沙发Sectional sofa

功能椅Function(al) chair转椅Swivel chair

单人位Single chair、One seater sofa两人位Love seat、Two seater sofa三人位Sofa、Three seater Sofa转角Corner躺位Chaise loungue

坐垫Seat Cushion靠背backrest扶手armrest

坐前front沙发背部back沙发侧面Side

沙发脚sofa leg沙发皮套leather coat车缝sewing车缝线sewing line针脚Stitch

针脚很均匀/宽松/紧凑。The stitches are neat/loose/tight.

包装相关:

包装packing包装方式Packing method

无纺布Non-woven(fabric)气泡袋Bubble Bag

毛毯Woolen blanket塑料编织袋Plastic bag

纸箱Carton五层瓦楞纸5 ply corrugated board天地盒Cover and tray carton纸箱强度Carton strength

散装in bulk

装运相关:

装柜Load the container装柜量Loading quantity

《辞职报告中英文对照.doc》
辞职报告中英文对照
将本文的Word文档下载到电脑,方便收藏和打印
推荐度:
点击下载文档

相关推荐

祝福语实习报告辞职报告策划书口号检讨书介绍信导游词社会实践报告求职信协议书委托书证明承诺书自我介绍自我评价自我鉴定广告词申请书活动方案
下载全文