2020-03-02 14:13:50 来源:范文大全收藏下载本文
English
Chinese acceptable level
可接受的程度 active pit alarms
泥浆槽警报 active pit level
泥浆池液位 aft
船尾
aft catwalk
船尾钻杆走道 Aft Conveyor
船尾输送机 Aft Mouse Hole
船尾接管孔 AFT PRS
船尾PRS air hoist
气动绞车
air hoist line
气动绞车大绳 air regulator
空气调节器 alarm meage
警告短信 all clear
解除警报信号 Approved by:
批准人:
arm extend joystick
悬臂伸展操纵杆 arms
悬臂
Aistant Driller
副司钻 At.Driller
副司钻 auto mode
自动模式 barrier tape
栅栏带 BHA
底部钻具组合
bit and stabilisers
钻头和稳定器 Bit Breaker
钻头装卸器 blocks
滑车
blue tugger
蓝色卷扬机 BOP
防喷器
bottom hole aembly
井底孔组合 bottoms up
循环一周 box end
内螺纹端
Boxes and pins
内螺纹和外螺纹 break circulation
恢复循环
Carriage Raise-Lower
钻车升/降 carriages
钻车
cased hole
已下套管井 casing box
套管内螺纹端 casing drift
套管整形器 casing elevator
套管吊卡 casing finger
套管手指 casing jobs
下套管作业
Casing Power Tong
套管动力吊钳 Casing Roughneck
套管钻工 casing size
套管尺寸 Casing Tong
套管吊钳 Casing Tong
套管钳 CCW
逆时针方向 cement head
水泥头 cement stand
水泥立根 chain hoist
链式起重机 chain tong
链钳 Chain tongs
链钳 check list
检验单
Cherry picker
车载升降台 cherry picker
车载升降台 claw
爪钩 claw
爪钩
CLAW CLOSE
爪钩关闭
clean and inspect
清理并检查 close acce stairs
邻近内部楼梯 close lower roller
关闭下辊 CLOSE TAILING ARM
关闭尾臂
close the handling tool
关闭装卸工具 collar clamp
卡箍
Company Man
公司人 control panel
控制面板 conveyor
输送机 conveyor belt
输送带 Core Barrel
岩心筒 core tube
岩心筒
counter balance
平衡锤 counter weight
重锤 Crane
吊车
Crane operator
吊车操作工 Crown Block
天车 csg
套管
cutting tool
切割工具
Date approved:
批准日期: Date iued:
发行日期: deadman
叉杆
debriefing
任务报告 deck crew
舱面人员
Deepwater Discovery
深水发现 degaer
除气器 Denso Tape
防蚀带 derrick
井架
derrick man
井架工 Derrickhand
井架工 Derrickman
井架工 dog collars
爪环 dolly
台车 Dope
丝扣油
down hole tools
井下工具 DP Operator
DP作业员 draw works
绞车
draw-works drum
绞车滚筒 Drill Collar
钻铤 drill crew
钻井队员 Drill Floor
钻台 Drill Line
大绳 Drill Pipe
钻杆 drill string
钻柱 Driller
司钻
drilling bails
钻井提环 drilling mud
钻井泥浆
Drilling parameters
钻井参数 drill-line tensioner
大绳张紧器 drive dolly
顶驱台车 Duct Tape
封管胶带 DWS
司钻工作站 elevator
吊卡
elevator adapter
吊卡适配器 Emergency Disconnect
紧急中断 Extend
伸出
Extend the arm
伸出推靠臂 fast-line tension
快绳拉力 Feeder
进料器
File name
文件名称 fill with pump
泵灌注 Finger board
指梁
Finger Position
手指位置 finger slot
指状槽 fingerboard
指梁 fingerboard
指梁
fingerboard mode
指梁模式 fish neck
打捞颈
Fishing Aembly
打捞组合
Fishing Aembly tools
打捞组合工具 FJE
平式接头吊卡
FJE claw close
平式接头吊卡爪钩关闭 Flex joint
挠性接头 Floor men
钻台工 Floorhands
钻工 flow check
流量检查 flow head
井口自喷装置
flush joint elevators
平式接头吊卡 Fore conveyor
船头输送机 Fore Mouse Hole
船头接管孔 FOSV
全启式安全阀 fresh mud
淡水泥浆
full gauge tools
全尺寸工具 full single
完整单根 fwd
船头
Fwd Mousehole
船头接管孔 Fwd PRS
船头PRS gas peak
气体峰值 goggles
护目镜 Grease
润滑脂 grip jaw
夹紧卡爪 hand signals
手势信号
handling equipment
装卸设备 handling tool
装卸工具 Handling Tool
装卸工具
handover sheet
交接班工作单 hazards
危害
Headache Ball
保险球 hold the pipe
握住钻杆 hole
井眼
hole condition
井眼状况
hole fill up sheet
井眼灌注工作单 Hook
大钩
Hook Position
大钩位置
horizontal position
水平位置 hose
软管
hydraulic hose
液压软管 IBOP
内部防喷器 ID
内径
Index Procedure
索引程序 inner barrel
内岩心筒 insert plate
嵌入板 inserts
卡瓦座
Interlock Override
互锁超控 iron roughneck
铁钻工 jaw
卡爪 jaws
卡爪
jetting aembly
喷射组合 joint of casing
套管接头 keypad
键盘
kill manifolds
压井管汇 KT Ring
KT环
landing string
接地钻柱 latch
簧闩
Lay Down
放倒 lift cap
提升罩 lift subs
提升接头 lifting bails
吊环
Logging unit
测井装置
Lost Control Of Fingerboard
指梁失控 main protective sheath
主保护套 man riding
载人
Manning requirements
人员配备要求 Manriding Checklist
载人清单 Manriding Work
载人工作 Manual Mode
手动模式 master bushing
转盘方瓦
Measurement While Drilling
随钻测量 Monkey Board
二层台 moon pool
月池 Mouse Hole
接管孔
mouse hole spider
接管孔卡盘 Mud bucket
泥浆桶 mud hose
泥浆软管 mud line
泥线
Mud Logger
泥浆录井工 mud manifold
泥浆管汇 mud mat
防沉板 mud pump
泥浆泵 mud return
泥浆回流
mud weight in
进口泥浆比重 mud weight out
出口泥浆比重 mud-logging unit
泥浆测井装置 MWD
随钻测量
None required
无要求
notify the bridge
通知驾驶室 OD
外径 off-load
卸载 offshore
海上 on shore
岸上
open hole time
裸眼时间 open position
打开位置 open the jaw
打开卡爪 Open the lower jaw
打开下卡爪 Operational Procedure
操作程序 Operations Engineer
操作工程师 Override pushbutton
【超控】按钮 P.A.
公共广播
parking system
停泊系统 pending position
待定位置
Permit Requirements:
准许证要求: pin end
外螺纹端 pin end
外螺纹端 pipe dope
管子涂料
pipe handler
钻杆操作器 Pipe Handler
钻杆装卸装置
pipe handler elevator
钻杆操作器吊卡 Pipe spinner
钻杆旋扣器 pipe stand
钻杆立根 pipe tally
钻杆记录 Pipe wiper
钻杆刮泥器
pit lo/gain
泥浆池增益/损失 Port Mid Crane
门口中间吊车 Pre-job
作业前
Pre-job Safety Meeting
工作前安全会议 preure test
压力测试 PRS
钻杆排放系统
PRS handling tool
模式识别系统装卸工具 Public Addre
扩音广播
pump stroke counter
泵冲程计数器 Pup Joint
短节 Purpose:
目的: Rabbit
清管器
RACKER CONFIGURATION
排管器配置 Radioactive Shield
放射护罩
radioactive source fishing
放射源打捞 radioactive work
放射性工作 radios
无线电
regular interval
有规律间隔 retract
缩回
retract arm
缩回推靠臂 retract the arm
缩回推靠臂 Review Procedure
审查程序 Reviewed by
审核人 Revision:
修订版: rig
钻机
rig camera
监控摄像机 rig floor
钻台
Rig Manager
海上钻机操作监督 RIH
下入井内 riser
立管
riser deck
立管甲板 riser hand
立管手阀 Riser Mode
立管模式 riser skate
立管板 roller
辊 rotary
转盘
rotary bushings
转盘补心 rotary table
转盘
rotate to fingerboard
指梁 Roughnecks
钻工
Routine Activity
例行活动 routine operation
例行操作 RPM
每分钟转数 run casing
下套管
running order
下入顺序 running speeds
下入速度 Running Tool
下送工具 safe procedure
安全程序
Safe Work Permit
安全工作许可证 Safeguards:
安全措施: Safety barriers
安全栅栏 safety clamp
安全夹 Safety harne
安全带
safety precaution
安全预防措施 saver sub
保护接头
Schlumberger Wireline
斯伦贝谢钢丝绳 select the working slot
选择工作槽 Senior Supervisor
高级监督 sensor
传感器
set back area
立根盒 set down
坐放
Shale Shaker
泥浆振动筛 shipping crate
板条箱 shoe
管鞋
shoe joint
鞋管 single
单根
single joint elevators
单根吊卡 Single Mode
单杆模式 single pipe
单杆
sledge hammer
大锤 sling
吊索
slip handles
卡瓦手柄 slips
卡瓦
Slope Indicator
测角器 slot position
槽位 slug
段塞
snap Shot
快速嵌入
soft/weak formations
软弱岩层 spider
卡盘
spider slips
卡盘卡瓦 spider slips
卡盘卡瓦 split bushings
拼合衬套 split ring
拼环 spool piece
管段
stabbing guide
对扣引鞋 stabilizer
稳定器 stabilizers
扶正器 stand
立根
Stand Mode
立根模式 standby
待命 standpipe
竖管 staple
气钉 stiff arm
硬臂
stiffening arm
加强臂 stinger
插入管
stop automatically
自动停止 Subsea Engineer
海底工程师surge preures
波动压力 tag lines
抓斗稳定索 tailing arm
尾臂
Task Specific THINK Procedure
TD
顶驱
TD Torque
顶驱扭矩
Telescopic Joint
伸缩接头 THINK Plan
思考计划 Thread compound
螺纹油 thread lubricant
螺纹润滑剂 Thread protector
护丝管箍 tight spots
缩径处 Tong die
吊钳牙板 tong jaws
吊钳卡爪 tongs
吊钳
Tool Joint
钻具接头 Tool pusher
钻井队长
特定任务的思考程序
toolbox meeting
工具箱会议 Toolbox Talk
工具箱会议 Toolpusher
钻井队长
top connection
顶部管接头 top drive
顶驱
top tool joint
顶部钻具接头 torque value
扭矩值
Torque Wrench
扭矩扳手
travel to well center
游走到钻井中心 traveling block
游车 trip drill
起下钻防喷训练 Trip sheet
起下钻工作单 trip tank
泥浆补给罐 Trip Tank
泥浆补给罐
TSTP
特定任务的思考程序 tubular
管件
Tubulars on Board
井场管材 tugger
卷扬机
tugger line
卷扬机钢丝 Unclamp
松开 unlatch
开闩
Unlatch Mode
开闩模式 Unlock
开锁
Upper Carriage
上钻车 Upper Claw
上爪钩 upper jaw
上卡爪
Upper Pipe Rams
上闸板 valve
阀
V-Door
井架大门
vent manifold
排出管汇 vent ports
排出口
vertical position
垂直位置
veel maneuvering operation
veel motion
船只运动 visqueen
维士昆 visual check
目测 Watchman
看守工
weight indicator
指重表 weight indicator
重量指示器 Well Centre
油井中心 wellhead
井口 Wire brush
钢丝刷
wireline sheaves
钢丝绳滑轮 work basket
工具筐
船只调动作业 Work Permit
工作许可证 wrench
扳手 slips
卡瓦
latched row
锁存行
service eng.
服务工程师
售后服务工程师 croover
转换接头
转线轨道
REG box end Lifting Nubbin
变速箱端提升小片
变速内螺纹端提升小片 Port mid-ship crane
港口船中起重机
港舯起重机 MRLD Tool
多速率线性检测工具
drill floor aft.
钻台船尾
rig floor tugger
钻台起重机
link tilt
吊环
(可用作动词) double of drill pipe
双钻杆
DC finger
back-out
退出
做动词用 storage rack
存放架
transit water line
经纬仪水线
cursor rail
指针轨
转动臂轨 load rating
额定负荷
over water work
水上作业
2ea spanners
双头扳手
inertia reel
惯性卷筒
unhook
脱钩
动词 unlatch
开闩
动词
stowed position
存放位置
upper deck
上甲板
captain
船长
mate
大副
boatswain
水手长
securing bolt
紧固螺栓
life vest
救生衣
top tubular
顶部管件
attach…to…
系上
pad eyes
系缆环板
垫眼 turnbuckle
螺丝扣
boomer
自动木栅
Tripping tool
起下钻工具
table bowl
转盘滚筒
side outlet
侧向出口
rig tong
钻机大钳
swivel
旋转接头
水龙头 Telescopic Joint
伸缩节
centre hole
中心钻孔
Web Sling
吊货索网
PA announcement
公共广播公告
Bosun
水手长
Shackle
卸扣
Large Yellow Web Sling
大黄色吊货索网
red indicator line
红色指标线
shackle pin
卸扣栓销
bow of the shackle
卸扣的弓形
port amidships crane
左舷船中起重机 Trolley Bucket
台车吊桶
hydraulic lifting tool
液压提升工具
Lifting cap
提升罩
起钻时用的钻具护丝 Tugger from rigfloor
钻台卷扬机
catwalk tugger
钻杆走道卷扬机
spotter
侦查员
Snatch Block
紧线滑轮
crane spreader hook
起重机吊钩
tail out
甩尾
动词 tail in
收尾
动词
logging line
录井大绳
funnel
漏斗
喇叭口 语译通-大青:
wireline
钢丝绳 tugger
卷扬机 tubular
管件
Trip Tank
泥浆补给罐 torque
扭矩
toolpusher
钻井队长 Tool Joint
钻具接头 TD
顶驱
tag lines
抓斗稳定索
snatch block
开口滑车??? sling
吊索 shackle
卸扣
saver sub
保护接头
Safe Work permit
安全作业许可证 safety clamp
安全夹 Running Tool
下入工具 Rotary Table
转盘 riser skate
立管板 rig floor
钻台 Pup Joint
短节
Pipe Racking Systems
钻杆排放系统
(PRS) Pipe Handler
钻杆装卸装置
(PH) Mud Gas Separator
泥气分离器
(MGS) Mouse Hole
接管孔 mousehole
接管孔
Measurement While Drilling
随钻测量
(MWD) jaw
卡爪
Iron Roughneck
铁钻工 inner barrel
内岩心筒 hose
软管
Handling Tool
装卸工具
flush joint elevators
平接式吊卡 Flush Joint Elevator
平接式吊卡 flow head
井口自喷装置 fingerboard
指梁 Expre Head
快车头 elevator
吊卡 drill string
钻柱 Drill Pipe
钻杆 Drill Floor
钻台 driller
司钻
drill crew
钻井队员 derrick
井架
Cursor Rail
游标轨 crane
起重机 core bbl.
岩心筒 conveyor
输送机
Coil Tubing Frame
挠性管框架
Coiled Tubing
饶性油管
(CT???)
CMC
CMC chain tong
链钳 Bop
防喷器
BHA
底部钻具组合
Auxiliary Pipe Handling System
辅助钻杆装卸系统
At.Driller
副司钻 Aist Driller
副司钻 AFT PRS
船尾PRS VHF radio
甚高频无线电 upper arm
上臂 thread
螺纹 drag chain
拉链
aft mouse hole
船尾接管孔 Aft air hoist
船尾气动绞车 ??? Upper Carriage
上钻车 mud mat
防沉板
chain hoist
链式起重机
(APHS))( bail
吊环
joint of casing
套管接头 control panel
控制面板
tension adjust bolt
张力调节螺栓 riser spider
立管卡盘 KT Ring
KT环 Drill Collar
钻铤
air tugger
气动卷扬机 Tool Pusher
钻井队长 sheave
滑轮
THINK Plan
思考计划
MRLD Tool
多速率线性检测工具
FOSV
全启式安全阀
(Full Opening Safety Valve) FWD MOUSE HOLE
船头接管孔 claw
爪勾
traveling block
游车 safety harne
安全带
Review Procedure
审查程序 Lift Sub
提升短节 Drill Line
大绳
Derrickman
井架工 core frame
岩心架
catwalk tugger
走道卷扬机
Pre-job Safety Meeting
作业前安全会议 Fwd air hoists
船头气动绞车 Coil Tubing Track
挠性油管架 Torque Wrench
扭矩扳手 THINK Drill
思考训练 latch elevator
闩上吊卡 deck crew
甲板人员 Choke
阻气门
cherry picker
车载升降台 Casing Tong
套管钳 ton
吨
plc
可编程逻辑控制器
(翻译成PLC) wireline operator
钢丝绳操作工 tugger line
卷扬机钢丝
side door elevator
侧门吊卡 methanol tote tank
甲醇罐 grip jaw
夹爪
flowhead
井口自喷装置 cement head
水泥头 manrider
载人
Work Permit
作业许可证 shallow gas
浅层气 riding belt
载人带
casing spider slips
套管卡盘卡瓦 bushing
补心
blue tugger
蓝色卷扬机 standby
备用 mud line
泥线
landing string
接地钻杆 cmt head
水泥头
Upper Pipe Rams
上闸板
(UPR) Tailing Arm Claw
尾臂爪钩 roller
辊
rig floor tuggers
钻台卷扬机 permit to work
作业许可证
Fingerboard Active
【指梁活动】 drill floor tuggers
钻台卷扬机 web sling
吊货索网
sledge hammer
长柄大锤
Sequence Mode
【次序模式】 retract position
收回位置 pin end
外螺纹端
Operation procedure
操作程序 Monkey Board
二层台 Manual Mode
手动模式 link tilt
吊环倾斜装置 inner Bbl
内岩心筒
Gantry Crane
龙门起重机 finger board
指梁
Choke Manifold
节流管汇 casing Bails
•套管提环 standpipe
竖管 stabilizer
稳定器 roustabout
甲板工 cradle
钻架 catcher
卡头
wireline adapter
钢丝绳接头 storage area
存储区
stand of drill pipe
钻杆立根 Shale Shaker
泥浆振动筛 roughneck
钻工 roller jaw
辊卡爪
RIH
下钻
(run in hole) Racker Configuration
排管器配置 PRS handling tool
PRS装卸工具 mouse hole spider
接管孔卡盘 moon pool tugger
月池卷扬机 methanol
甲醇
man riding operation
载人作业 lift cap
提升罩
leg Sling bridle
吊索系船索 hole cover
孔盖
drill-line tensioner
大绳张紧器 drag chain bucket
拉链斗
dowell
dowell choke line
节流管汇 box end
内螺纹端 belly board
中间平台
air hoist line
气动绞车大绳 air hoist
气动绞车
aft conveyor
船尾输送机
“Lost Control Of Fingerboard”
“指梁失控” spider
卡盘
RBS
井架排立立根
(全称???) nut
螺母
floormen
钻台工 dolly
台车 barrel
岩心筒
APHS
辅助钻杆装卸系统
(Auxiliary Pipe Handling System ) Transmiion Control Protocol
•传输控制协议
(TCP) Reservoir Description Service
获得油藏描述服务
(RDS) Power Distribution Panel
配电面板
(PDP) Log While Drilling
随钻测井
(LWD) yellow tugger
黄色卷扬机 workbasket
工具筐
vertical position
垂直位置 upper jaw
上卡爪
Think proce
思考过程 tailing claw
尾爪钩
BOGIE SWITCH
台车开关 Subsea Engineer
海底工程师
single joint casing elevators
单根套管吊卡 shoe joint
管鞋套管节 sensor
传感器
riser claw
立管卡爪
radio communication
无线电通信
PRS PLC
PRS PLC
(全称???) Port crane
右舷起重机 moonpool
月池 joint
单根钻杆 Fwd PRS
船头PRS forward catwalk
船头钻杆走道
(???) flare boom
火炬臂
Emergency disconnect
紧急中断 core bbl
岩心桶
casing stand
套管立根 burner head
喷嘴头
booster line
增压管线
(大部分翻译错) bearing
轴承
Public Addre
公共广播
Internet Protocol
互联网协议
(IP) Wireline Sheave
钢丝绳滑轮 wellhead
井口
varco
varco trolley
台车
TDS wireline adapter
顶驱系统钢丝绳接头安装
(修改缩写的部分) T.D.S
顶驱系统
riser tailing arm
立管尾臂
Racker Pipe Mode
排管器钻杆模式 port amidships crane
左舷船中起重机 Work Sheet
工作表
port aft tugger
左舷船尾卷扬机 Pending Latches box
待定锁存框 parking control panel
停泊控制面板 lanyard
系索
Interlock Override Mode
•互锁超控模式
Hot Work Permit
热作业许可证
(大部分翻译错) hook position calibration
大钩位置校准 forward mouse hole
船头接管孔 fast-line
快绳 DPO
钻杆操作工
diverter running tool
分流器试车工具
(???试车工具错?) derrick log book
井架钻井日志
(有翻译错) choke
节流
chain tong tight
链钳上紧 bridge
驾驶室
bottom hole aembly
底部钻具组合
(BHA) ay
组合 annular
环空
“set down”
“坐放”
“P” Tank
“P”罐
(有翻译成“P”灰罐?) working slot
工作槽
tugger operator
卷扬机操作工 thread protector
护丝 test Joint
测试接头
TDS Wireline Adapter Installation
TDS钢丝绳接头安装
(TDS是否需要全称,需要全文统一)
spare set of elevators
备用吊卡 slip handles
卡瓦手柄
Samson post
吊杆柱
(???) safety sling
安全吊索 rotary bushings
钻盘补心 Riser Mode
立管模式
Pre Job safety meeting
作业前安全会议 pre-job meeting
作业前会议
Port Mid Ship Crane
左舷船中起重机
(有翻译成“港口中型船起重机”???) Port Aft
左舷船尾 poor boy
泥气分离器 pipe stand
钻杆立根 park position
停泊位置 hydraulic hose
液压软管 handling tool
装卸工具 forward end
船头端 floor man
钻台工 dump valve
放卸阀 cup tester
皮碗试验器 crew member
机组人员
counter weight
平衡锤
(字典解释为“平衡重”???) manrider tugger
载人卷扬机 kill mud
压井泥浆 kill line
压井线
jaw status
卡爪状态
Interlock Override
互锁超控 function test
功能试验
counter balance
平衡锤
(字典解释为“平衡重”???) Core Barrel
岩心筒
control system
控制系统 Casing Hanger
套管悬挂器 barrier tape
栅栏带 auto mode
自动模式
appropriate size
适当尺寸
psi
psi hanger
悬挂器 dope
丝扣油
supervisor
监督
(注意替换掉“监督员”)
spotter
观察员
(翻译方法比较混乱,需要重点替换) OIM
采油平台经理 Drillship
钻井船 drawwork
绞车
DHM
井下马达
(Down Hole Motors-注意这个缩写尽量用全称)
CDR
补偿双电阻率测井仪
(船头PRS从输送机吊起新的双电阻率测井仪。,这句翻译错,剩下没问题,注意替换)
weight indicator
指重表
(翻译不统一,全文注意) visual check
目测
(视觉检查?目视?注意替换) telescopic joint
伸缩接头 Stbd crane
右舷起重机 split ring
拼环 snub line
尾绳
Slope Indicator
测角器 red tugger
红色卷扬机 Red Alert
红色警告 poum belly
泥浆储罐
pipe joint
钻杆接头
(很多翻译成“钻具接头”) pipe dope
钻杆丝扣油
(很多翻译不一致???) pilot hole
领眼 outer Core
外岩心
man rider
人车
(安排一个人向上到顶驱系统并连接大钩解开软管到顶取系统制动出口。??这句有问题,注意查找) main deck
主甲板
lo-torque valve
低扭矩阀 lock pin
锁钉
leak tests
泄漏检测
jetting aembly
喷射组合 Index Procedure
索引程序 hot line
热线
Hook Position
大钩位置 green tugger
绿色卷扬机 fwd Mousehole
船头接管孔 Fore PRS
船头PRS flow check
流量检查 floor men
钻台工
FJE
平接式吊卡
(flush joint elevators-此处尽量使用全称) finger slot
手指槽
fingerboard mode
指梁模式 fast-line tension
快绳张力
escape route
逃生路线
(错误-需要修改) Emergency STOP
紧急停车 Crane Op
起重机操作工 chain block
链条滑车
cement aembly
固井组合
(有水泥组合??? cement 需要整体查找) BX elevator
BX吊卡 Bop transporter
防喷器传输器 air winch
气动绞车 aft tugger
船尾卷扬机 Aft Riser
船尾立管
veel maneuvering operation
船只调动作业 V-Door
井架大门
Upper Grip Jaw
上夹爪 swivel
旋转接头
Sub sea engineer
水下工程师
(海底工程师???全部替换) Sub Sea Eng.
水下工程师
(海底工程师???全部替换) spacer sub
隔离接头
poor boy degaer
泥气分离器 pipe wrench
钻杆扳手
pipe handler
钻杆装卸装置 man riding harne
载人带 lubricant
润滑剂
Lock Down Tool
锁定工具
left-hand control panel
左手边控制面板 single joint elevators
单根管子吊卡 racker
排管器
RKB
方钻杆补心
(全称???翻译不统一) Kick Off Aembly
造斜钻具组合 high preure testing
高压试验 hang off line
悬挂钢丝绳
gimble
万向接头
(注意译文中的批注???) Fore Mouse Hole
船头接管孔 drillstring
钻柱
Drill Collar Fingerboard
钻铤指粱
Dowell
Dowell
(文中有翻译成“道威尔”的,修改成英文) clamp cylinder body
夹具气缸体 W.H
井口 wrench
扳手
adapter
接头
(全部替换成“适配器”)
stabber
对扣 / 对扣工
(视情况而定,估计原文错误) shaker
振动筛
Accumulator
蓄电池
aft mousehole
船尾接管孔
air line
架空线
(翻译不统一) annulus
环空
APHS operator
辅助钻杆装卸系统操作工
(APHS的缩写替换回来-操作者全文替换为操作工)
API
API
(“美国石油学会标准”需要替换成API,查找) YELLOW ALERT
黄色警报
(“警报”和“警告”需要全文替换) work vest
工作汗衫 work site work basket
工具筐 work area
工作区域 wireline head
钢丝绳头
Wireline Fishing
绳索式打捞 wire brush
钢丝刷 WH
井口
wellhead joint
井口单根管子 welder
焊工
weight bar
加重杆 wedge
楔子
wear bushing
抗磨补心
warning sign
警示牌
(翻译不统一的多) visqueen
维士昆 vent ports
排出口
vent manifold
排出管汇 upper column
上柱 Upper Claw
上爪钩
unscrew
拧开
(翻译不统一?是否需要替换?) unlatch
开闩 well test
试井 well testing
试井
umbilical
脐管
(翻译“控制管缆”“控制”;“井口自喷装置位置的确定将按照软管和控制”,这句查找一下,有误) tubing spider
油管卡盘 torque value
扭矩值
toolbox meeting
工具箱会议 Tidal
潮汐
(翻译不统一) test run
试运行
(有试运转和试车-需要统一) tension indicator
张力指示器 Tensioner
张紧器 TD Torque
顶驱扭矩
T-Bar
T型钢
(这个\"型\"?形?) taglines
抓斗稳定索 suction lines
吸入管线 subsea
水下 string
钻柱
stinger
插入管
(=stinger pipe) stiff arm
硬臂
stbd
右舷
(???) starboard
右舷 staple
气钉
stb
右舷
(修改“标准”“插头”) stand selector
立根选择器 standpipe manifold
竖管管汇 Stand Mode
立根模式 stabbing guide
对扣引鞋
SSTT
海底试验树
(全称?须全文统一缩写的问题) spreadsheet
电子表格 snap Shot
快速嵌入 slot position
槽口位置 slips
卡瓦
Single Mode
单根模式 side entry sub
旁通接头 shipping crate
板条箱 shims
垫片
shear rams
剪切式闸板 serial number
序列号 Seal Aembly
密封组合
Schlumberger
斯伦贝谢
(有翻译成Schlumberger,统一成译文或原文) scaffolding
脚手架 safety line
安全绳 safety gates
安全闸门 safety device
安全装置 safety chains
安全链
Safe Operation
安全作业
(操作和作业,需要统一-比较严重) rubber
橡胶
ROV
遥控潜水器
(翻译大部分不一致-)
routine operation
例行作业
(还是操作和作业的问题-) pneumatic
气动 plywood
胶合板
pipe weight
钻杆重量值 Pipe Rams
闸板 pipe ram
闸板
pin protector
外螺纹端护丝
pending position
待定位置
(这个需要核实) Normal Mode
正常模式 N.M.HWDP
无磁加重钻杆
mud weight
钻井液密度
(字典的解释)
mud pump
钻井液泵
(mud这个词可能全篇错,需要全文查找) Hsg.
外壳
Mud loggers
钻井液录入工 mud engineer
钻井液工程师 parking system
停泊系统 pad eye
吊眼 padeye
吊眼 overshot
打捞筒
outer saddle
外鞍
(saddle这个词需要单独看看) outer barrel
外岩心筒 OD
外径
obstruction
障碍物 O.D
外径
rolling cradle
滚轮托架
(rolling和cradle单独出现的时候也要查) riser hand
立管手阀 riser deck
立管甲板 rig tongs
钻机大钳 rigfloor
钻台
rig crew
钻井班
(翻译不一致,按照石油字典解释修改成\"钻井班\") regulator
调节器
radioactive source
放射源 Racker Mode
排管器模式
cmt
水泥
(cement-水泥/固井) bridle
系船索 booster
助力器 Boatswain
水手长 checklist
清单 cylinder
气缸体
crewmember
工作班人员 collar
钻铤 B.O.P
防喷器 bicycle
缆车
commiioning
试车 chicksans
高压旋转接头 bypa
旁通阀
brace
拉杆
(翻译不统一) Pumpman
泵工
bearing retainer
轴承护圈 At driller
副司钻 casing job
套管作业 casing box
砂箱
Cable Cutter
缆绳切割器 casing size
套管尺寸
Casing Roughneck
套管钻工 casing joint
套管接头 cement job
固井作业
cement expre
水泥快车
(这个词不确定!!!) casing string
套管柱
Company Representative
公司代表
choke valve
节流阀
(翻译不统一) choke panel
阻流器盘 conductor pipe
导管 PA
公共广播 Portable radio
便携式无线电 Pump man
泵工
stack
组
(防喷器组还是防喷器堆??) Aux Transporter
辅助运输机 casing elevator
套管吊卡
block hook
游车大钩
(block这个词需要全文查找,核实) Bit Breaker
钻头装卸器 cement hose
水泥管 cement hand
固井手 casing finger
套管手指
cement stinger
注水泥插入管 Cement Stand
水泥立根 spacer bar
隔离杆 pipe guide
钻杆导向器 moon pool
月池 metric Tons
公吨
manual elevator
手动吊卡 manifold preure
管汇压力 isolation valve
隔离阀 inertia reel
惯性卷筒
idler sheave
惰轮
(翻译不统一) bails
提环
core tube
岩心筒
conveyor deck
输送板 C plate
C板
croover
转换接头 csg
套管
Crown Sheave
天车滑轮
(这个翻译不统一的多,天车crown,翻译混乱) Crown Block
天车
(这个翻译不统一的多,天车crown,翻译混乱)
CT Frame
挠性油管架
(CT-coiled tubing-这个词需要单独查-翻译比较混乱) Cyber chair
数码座椅 Cyberbase
数码基地
degaer
除气器
(???) deadman
叉杆
Denso Tape
防蚀带 derrick man
井架工
DP Operator
钻杆操作工
Draw-works tugger
绞车卷扬机 drillfloor
?钻台 drill-line
大绳
drilling operation
钻井作业 Drillquip
钻井设备 Electrician
电工
Duct Tape
封管胶带 epoxy
环氧 eng
工程师 end slot
结束槽
fingerboard graphic
指梁图示
(???) Fishing Aembly
打捞组合
(???) fingerboard slot
指梁槽口 flange
法兰
fish neck
打捞颈 Floorhands
钻工 Float Sub
浮标接头 floorman
钻台工 flow rate
流量 Flow Line
出油管 fore
船头
Fore conveyor
船头输送机 forward conveyor
船头输送机 Formation Integrity
地层完整性
ft.lbs
ft-lbs
(注意,把翻译成“磅力”等其他都改成英文) Fwd Conveyor
船头输送机 gamma
伽马 gallon
加仑 grease
润滑脂
guidelines
操作指导
(翻译不一致) Guide Rails
导轨
harne
安全带
(大部分这样翻译-需要查证) headache ball
保险球 Hook Load
大钩载荷 I.D
内径 ID
内径
IBOP
内部防喷器 injection port
注入口 jar
震击器
JSA
作业安全分析
klbs
klbs
(译文全部改为英文) lifting bail
吊环 liner
内衬
logbook
井架日志 locking eyes
锁眼
Maintenance Mode
维修模式 manifold
管汇
Manriding Operating
载人作业 mate
大副
manufacturers
制造商 mousing wire
防脱钩绳 PPE
个人防护设备 precautions
预防措施 preure gauge
压力计
pre-job toolbox
作业前工具箱 spanner
扳手
人人范文网 m.inrrp.com.cn 手机版